SHENZHEN GUIYUAN INDUSTRY DEVELOPMENT CO.,LTD
Http://www.carymart.com E-Mail: [email protected]
5000 Meters RF Wireless Receiver (Model 0020104)
Receiver Feature:
Wireless control, easy to install.
Waterproof case with waterproof connectors.
The receiver can be installed outdoors.
High power, each relay output can work at maximum current 30A.
Super long range, with a transmitter to form a complete set, the working distance can reach 5000m in an open ground.
Feedback function: can let the user know whether he/she had already connect the transmitter and receiver successfully in such a long distance.
Two ways working mode, when the receiver gets the signal of transmitter, it will immediately send a return signal to the transmitter.
External magnetic sucker antenna with 5meters cable, the antenna can be installed outside the building to get better working distance.
With manual terminals, can connect a manual switch or a sensor to control the receiver.
America imported chips, which can ensure reliability and assure the high quality of the products.
Relay output, can be used in home automation, such as security system, remote control lights, motors, Doors / Locks / Windows / Blinds / Cars, and
various equipment.
It also can be used in agriculture and industry automation, such as long range and high power remo te control devices.
Wireless remote control products on land, water and air, especially in a long distance, such as farm, pasture, offshore
unmanned operation, field call,
remote security alarm, unmanned aerial vehicle, etc.
You can turn on/ off the receiver with transmitter (remote control) from any place within a reliable distance; the wireless RF signal can pass through
walls, floors and doors.
With characteristics of reverse power protection and over current protection
Reliable control: The transmitter (Encoding) and the receiver (Decoding) use the custom code.
One/several transmitters can control one/several receivers simultaneously.
You can use two or more units in the same place.
Receiver Parameters:
Model No. S1PUW-DC06-ANT2 / S1PUW-DC09-ANT2 / S1PUW-DC12-ANT2 / S1PUW-DC24-ANT2
Power Supply (Operating Voltage): DC6V (S1PUW-DC06-ANT2), DC9V±1V (S1PUW-DC09-ANT2), DC12V±1V (S1PUW-DC12-ANT2), DC24V±2V
(S1PUW-DC24-ANT2)
Working Frequency: 433.92MHz
Channel: 1 CH
Control Modes: Toggle, Momentary, Latched
Output: Relay output (Normally open and normally closed)
Working Voltage Range of Relay: AC110~240V or DC0~28V
Maximum Working Current of Relay: 30A
Static Current: ≤6mA
PCB size: 140mm x 73mm x 18mm
Case size: 192mm x 100mm x 45mm
Work with custom code transmitters.
Notice:
The receiver can only pair six different model transmitters, model CC-1, CC-2 CC-4
，
CCW-1, CCW-2 or CCW-4. You can use one transmitter CC-4
with four buttons to control two receivers.
External Magnetic Sucker Antenna:
Frequency Range: 300~450MHz
Impedance: 50Ω
Antenna Length: 15cm
Cable Length: 5meters, we also can offer longer cable, such as 10meters or 30meters.
Weight: 85g
Anti-interference, waterproof, shielded wire set inside
Magnetic stand design for easy to install
With SMA connector
Usage (with the transmitter):
Connect DC power to terminal “+” and “-“.
Initial state of relay output terminals: Terminals A and B are Normally Open; Terminals A and C are Normally Closed.
Setting different control modes (We have set the receiver as Toggle control mode before delivery. If you want to use other control modes, do as
following operation):
Setting control mode Toggle (with transmitter CC-1): Turn on the first bit of the dip switch.
Control mode Toggle: Press -> On; Press again -> Off.
Press the button of the transmitter: Turn on the relay (connect A and B, disconnect A and C)
Press the button again: Turn off the relay (disconnect A and B, connect A and C)
Setting control mode Momentary (with transmitter CC-1): Turn on the first and the second bits of the dip switch.
Control mode Momentary: Press and hold -> On; Release -> Off.
Press and hold button of the transmitter: Turn on the relay (connect A and B, disconnect A and C)
Release the button: Turn off the relay (disconnect A and B, connect A and C)
Setting control mode Latched (with transmitter CC-2): Turn on the second bit of the dip switch.
