SAFETY INSTRUCTIONS (EUROPEAN)
The conductors in the AC power cord are colored in accordance with the following code.
GREEN & YELLOW—Earth BLUE—Neutral BROWN—Live
U.K. MAIN PLUG WARNING: A molded main plug that has been cut off from the cord is
unsafe. NEVER UNDER ANY CIRCUMSTANCES SHOULD YOU INSERT A DAMAGED
OR CUT MAIN PLUG INTO A POWER SOCKET.
IMPORTANT! FOR YOUR PROTECTION, PLEASE READ THE FOLLOWING:
WATER AND MOISTURE: Appliance should not be used near water (near a bathtub, washbowl,
kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc). Care should be taken
so that objects do not fall and liquids are not spilled into the enclosure through openings.
POWER SOURCES: The appliance should be connected to a power supply only of the type described
in the operating instructions or as marked on the appliance.
GROUNDING OR POLARIZATION: Precautions should be taken so that the grounding or polar-
ization means of an appliance is not defeated.
POWER CORD PROTECTION: Power supply cords should be routed so that they are not likely
to be walked on or pinched by items placed upon or against them, paying particular attention
to cords at plugs, convenience receptacles, and the point where they exit from the appliance.
SERVICING: The user should not attempt to service the appliance beyond that described in the
operating instructions. All other servicing should be referred to qualified service personnel.
FUSING: If your unit is equipped with a fuse receptacle, replace only with the same type fuse.
Refer to replacement text on the unit for correct fuse type.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL! THIS UNIT CONTAINS HIGH
VOLTAGE INSIDE!
CAUTION
RISK OF ELECTRIC SHOCK
REPLACEMENT PARTS LIST
(for circuit cards)
LIMITED WARRANTY
Your Carvin product is guaranteed against failure for ONE YEAR unless otherwise stated. Carvin will
service and supply all parts at no charge to the customer providing the unit is under warranty. Shipping
costs are the responsibility of the customer. CARVIN DOES NOT PAY FOR PARTS OR SERVICING OTHER
THAN OUR OWN. A COPY OF THE ORIGINAL INVOICE IS REQUIRED TO VERIFY YOUR WARRANTY.
Carvin assumes no responsibility for horn drivers or speakers damaged by this unit. This warranty
does not cover, and no liability is assumed, for damage due to: natural disasters, accidents, abuse,
loss of parts, lack of reasonable care, incorrect use, or failure to follow instructions. This warranty
is in lieu of all other warranties, expressed or implied. No representative or person is authorized to
represent or assume for Carvin any liability in connection with the sale or servicing of Carvin prod-
ucts. CARVIN SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.
When RETURNING merchandise to the factory, you may call for a return authorization number. Describe
in writing each problem. If your unit is out of warranty, you will be charged the current FLAT RATE for
parts and labor to bring your unit up to factory specifications.
HELP SECTION
1) AMP WILL NOT TURN ON
Check the power to the amp. Check for tripped circuit breakers, unplugged extension cords or power-
strip switches that may be turned off. Check the fuse. If a dark brownish color or no wire can be
seen within the glass tube, then replace. The amp may be perfectly fine but occasionally a fuse
may blow because of high AC voltage surges. After the fuse has been replaced with the proper
Slow Blow value and if the fuse fails again, the amp will require servicing.
2) NO OUTPUT with POWER LED light ON
Check the speaker cable. If OK, it’s possible that a speaker jack is defective. Check the SEND &
RETURN jacks as one of these jacks could be defective. Insert a guitar cord between these two
jacks to test. Defective jacks will require servicing.
3) KEEP YOUR AMP LOOKING NEW
Use a damp cloth to wipe the controls on the front & rear chassis panels. Wipe dry! Brush the lint
off the Duratuff II™ covering.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
This symbol is intended to
alert the user to the pres-
ence of uninsulated “dan-
gerous voltage” within the
product’s enclosure that may be of suf-
ficient magnitude to constitute a risk of
electric shock to persons.
This symbol is
intended to alert the
user to the presence of
important operating
and maintenance (servicing) instruc-
tions in the literature accompanying
the appliance.
Carvin P/N
Description
Ref. Des.
06-40050
1 EACH TERMINAL VERT MALE PC MTG .250
QC5
06-40060
5 EACH TERMINAL 90dg MALE PC MTG .250
QC1,
QC2, QC3, QC4, QC6
21-06457
3 EACH JACK .250" 7 PIN 24MM PLASTIC
J10*,
J11, J12
21-31100
1 EACH RECEPTACLE AC W/FAST-ON CHASS
PL1
21-40020
1 EACH JACK RCA DUAL PC VERTICAL MTG
J4
21-50345
4 EACH JACK .250" PHONE MONO PCB MTG J1, J2,
J3, J5
23-03529
2 EACH FUSEHOLDER CLIPS 3AG VERT MTG F1
23-11004
4 EACH CONNECT HEADER 4 PIN STRAIGHT
H1A,
H1B, H7A, H7B
23-11010
2 EACH CONNECT HEADER 10 PIN STRAIGHT
H3A,
H3B
23-15605
1 EACH CONNECT HEADER .156" 5 PIN
H2
25-02201-1
3 EACH ASSEMBLED SWITCH AND CAP
S1, S2,
S3
41-47322
1 EACH CAP MYLR .0470UF 250VAC BOX
C33
42-47251-1
2 EACH CAP ELEC 4,700 MFD 50V 20%
C98, C99
47-22151
1 EACH CAP ELEC 220 MFD 50VOLT 10%
C90
47-10225-1
2 EACH CAP ELEC 1,000 MFD 25V 20%
C94, C96
49-10312
16 EACH 0.01UF SMT 10% FILM 080550V
C104,
C17, C21, C22, C23, C24,C28, C3, C51, C6, C65*, C73*, C8
C82*, C93, C95
49-10451
6 EACH 0.1 uF SMT 10% FILM 1206 50V
C1, C14,
C7, C71*, C72*, C74*
49-22035
15 EACH SMT CAP 22uF 35v ELECTROLITIC
C10,
C100, C102, C107, C108, C12, C25, C26, C29, C47*, C48,
C55*, C56*, C60, C91
49-22212
3 EACH 0.0022UF SMT 10% FILM 0805 50V C106, C76*,
C78*
49-22312
1 EACH 0.022UF SMT 10% FILM 0805 50V
C20
49-25152
3 EACH 220PF SMT 5% CERAMIC 0805
C27,
C34, C92
49-27052
2 EACH 27 PF SMT 5% CERAMIC 0805
C30, C49
49-33152
2 EACH 330PF SMT 5% CERAMIC 0805
C11,
C52*
49-33212
3 EACH 0.0033UF SMT 10% FILM 0805 50
C16,
C19, C75*
49-33312
2 EACH 0.033UF SMT 10% FILM 0805 50V
C79*, C9
49-39052
5 EACH 39PF SMT 5% CERAMIC 0805
C46,
C50, C53, C54, C69*
49-47312
7 EACH 0.047UF SMT 10% FILM 0805 50V
C13,
C18, C31*, C32, C4, C62, C77*
49-56152
3 EACH 560PF SMT 5% CERAMIC 0805
C15,
C64, C81*
49-82052
7 EACH 82PF SMT 5% CERAMIC 0805
C103,
C2, C5, C67*, C70*, C80*, C83*
55-03300
4 EACH RES .33 OHM 5W 5% SB VERT
R113,
R114, R127*, R128*
58-00035
4 EACH 0.0 SMT JUMPER 1206
R156*,
R51, R54, R130
(B1, B2, B3, B4, B5 PB100 ONLY)
58-02207
1 EACH 22 SMT 1W 2512 20%
R42
Carvin P/N
Description
Ref. Des.
58-10015
2 EACH 10.5 SMT .25W 1206 1%
R31, R32
58-10035
11 EACH 1K SMT .25W 1206 1%
R101,
R102, R111, R131, R133, R136*, R150*, R38, R43, R86, R99*
58-10045
16 EACH 10K SMT .25W 1206 1%
R120,
R121, R167*, R17, R178*, R18, R186*, R24, R25, R26, R69,
R70, R94, R30, R115*, R139*
58-10055
8 EACH 100K SMT .25W 1206 1%
R13,
R14, R78, R48*, R135*, R138*, R100, R105
58-10065
3 EACH 1M SMT .25W 1206 1%
R20,
R40, R41
58-15045
4 EACH 15K SMT .25W 1206 1%
R125,
R56, R67, R73
58-15055
3 EACH 150K SMT .25W 1206 1%
R175*,
R3, R79
58-22025
2 EACH 220.5 SMT .25W 1206 1%
R104,
R137*
58-22035
12 EACH 2.2K SMT .25W 1206 1%
R106,
R109, R110, R116, R124, R155*, R34, R35, R95*, R97*, R98*
R123
58-22045
16 EACH 22K SMT .25W 1206 1%
R10,
R11, R117*, R129, R140*, R23, R39, R5, R52, R55, R62
R63, R74, R8, R81, R9
58-22055
7 EACH 220K SMT .25W 1206 1%
R171*,
R173*, R177*, R65, R7, R77
58-27025
4 EACH 270.5 SMT .25W 1206 1%
R152*,
R53, R50, R76
58-33035
4 EACH 3.3K SMT .25W 1206 1%
R21,
R22, R75, R90
58-33045
6 EACH 33K SMT .25W 1206 1%
R12,
R57, R60, R83, R85, R29
58-36055
4 EACH 365K SMT .25W 1206 1%
R169*,
R68, R82, R93*
58-39035
2 EACH 3.9K SMT .25W 1206 1%
R172*,
R174*
58-43045
1 EACH 43K SMT .25W 1206 1%
R64
58-47015
3 EACH 47.5 SMT .25W 1206 1%
R112,
R119*, R89
58-47025
2 EACH 470.5 SMT .25W 1206 1%
R1,
R146*
58-47035
6 EACH 4.7K SMT .25W 1206 1%
R132,
R168*, R170*, R176*, R91, R88
58-47045
16 EACH 47K SMT .25W 1206 1%
R103,
R107, R108*, R118, R15, R166*, R19, R192*, R27, R28
R6, R37, R71, R72, R84, R96*
58-47055
3 EACH 470K SMT .25W 1206 1%
R92, R4,
R66
58-68015
1 EACH 68.5 SMT .25W 1206 1%
R80
58-68025
2 EACH 680 SMT .25W 1206 1%
R151*,
R49
58-68035
5 EACH 6.8K SMT .25W 1206 1%
R33,
R36, R87, R122, R16
58-68045
1 EACH 68K SMT .25W 1206 1%
R61
58-91025
3 EACH 910.5 SMT .25W 1206 1%
R190**,
R191**, R44
60-00142
2 EACH TRANS NPN TIP142 TO-218
Q32,
Q34*
60-00147
2 EACH TRANS PNP TIP147 TO-218
Q31,
Q33*
Carvin P/N
Description
Ref. Des.
60-75200
4 EACH DIODE GEN RECT MR752 6A 200V
D31,
D32, D33, D34
60-50253
1 EACH OPTO ISOLATOR VACTROL AXIAL
OP1
60-55500
4 EACH TRANS 2N5550 HV NPN 250V T0-92
Q11,
Q2, Q23*, Q25*
60-75320
3 EACH LED RED DIFFUSED 3MM T-1.00
D1,
D2, D3
60-78120
1 EACH REGULATOR VOLTAGE 12 +V 500mA
Q26
60-79120
1 EACH REGULATOR VOLTAGE 12 -V 500mA
Q27
62-04391
1 EACH TRANSISTOR SMT MMBF4391LT1
Q14
62-04739
3 EACH SMT DIODE ZENER 4739
Z11,
Z12, Z13
62-06001
4 EACH DIODE ULTRA FAST 600V 1A SMA
D26,
D35, D36, D37
62-19140
11 EACH 1N914 HI SPD SMT 250mW DIODE
D10,
D11, D13, D14, D4, D5, D6, D7, D8*, D9*, D12
62-29010
1 EACH NJM2901SMT SNGLE SUPPLY
A6
62-45650
9 EACH NJM4565 SMT DUAL HI FREQ
A11*,
A8*, A9*, A1, A10, A2, A3,
62-54001
16 EACH MMBT5401LTI PNP SOT-23 SMT
Q10,
Q12, Q13, Q15, Q16*, Q17*, Q21*, Q24*, Q3, Q4, Q5, Q6,
Q9, Q22, Q28
62-55500
5 EACH MMBT5550 NPN SOT-23
Q1,
Q19*, Q20*, Q7, Q8
70-05713
2 EACH RELAY SPDT 12A@120VAC/24V COIL
K1,
K2*
70-21050
1 EACH FUSE ABC 5.00A FAST 6.35X32MM
F1
71-09252
3 EACH POT 9 "D-P" 25F B50K-CC
P2,
P3, P4
71-09253
4 EACH POT 9 "D-P" 25F B50K-
P1,
P5, P6, P7
71-10320*
5 EACH FADER 20MM SL20V3-B10K-L15D(G)
P8*,
P9*, P10*, P11*, P12*
58-18035**
2 EACH 1.8K ON PB100
**R190,
**R191
