Carrier ZS Application Manual Download Page 13

Page: 13 / 49

Creating Snap control programs for ZS Sensors

ZS Sensor

Applications Guide

Step 3: Add Binary Sensed Value Input microblocks if using ZS Pro

motion sensor

From the

Net I/O

microblock menu, add one

Binary Sensed Value Input

(

BSVI

) microblock that will read a

binary value from up to 5 ZS motion sensors, and makes the value available to the control program on an output

wire. If the Rnet has more than one ZS motion sensor, the microblock's combination algorithm determines

whether the output value is based on a single sensor or all sensors having the same value.

Rnet Tag

All values from a ZS Sensor must have an Rnet tag that defines what type of

information this microblock's value represents.

NOTE

If the Rnet tag droplist does not have the tag you want, you can create

a custom tag in Snap.

Index/Enable

The Index number corresponds to the ZS sensors defined in the Sensor

Binder microblock. Check

Enable

for each sensor that you want to include in

the combination algorithm used to determine the output value of the

microblock.

Combination Algorithm

If using more than 1 sensor, select how the enabled sensors' values are to

be combined to determine the microblock's output value. Select:

And

to output 1 if all sensors have a value of 1, otherwise output 0

output 1 if any sensor has a value of 1, otherwise output 0

Show on Sensors

Select

Local Value

to have each enabled ZS Pro or Pro-F sensor display its

individual sensed value, or

Calculated Value

to have each ZS sensor display

the value determined by the

Combination Algorithm

Show on

Check the ZS Pro or Pro-F sensor screen(s) that you want this microblock's

value displayed on.

Show text

Enter the text that the ZS sensor's display will show with the microblock's

output is off or false (inactive) or when it is on or true (active).

Inactive Text

The

Inactive Text

your system displays when the microblock's output is off, or

false.

Active Text

The

Active Text

your system displays when the microblock's output is on, or

true.

Summary of Contents for ZS














































Search results

Summary of Contents for ZS

Reviews:

Brands by name

Popular brands

Carrier ZS, Application Manual

Search results

Summary of Contents for ZS

Reviews:

Brands by name

Popular brands