background image

  

 

 

WARNING: If the information in this manual
is not followed exactly, a fire or explosion may
result causing property damage, personal in-
jury or loss of life.

— Do not store or use gasoline or other flam-
     mable vapors and liquids in the vicinity of
     this or any other appliance.

— WHAT TO DO IF YOU SMELL GAS:
    • Do not try to light any appliance.
    • Do not touch any electrical switch; do not
       use any phone in your building.
    • Immediately call your gas supplier from a
       neighbor's phone. Follow the gas supplier's
       instructions.
    • If you cannot reach your gas supplier, call 
       the fire department.

— Installation and service must be performed
     by a qualified installer, service agency or
     the gas supplier.

®

HEATING & COOLING

MULTIPOISE, CONDENSING

58MCA, 58MVP, 58MXA

USER'S INFORMATION MANUAL FOR
THE OPERATION AND MAINTENANCE
OF YOUR NEW GAS-FIRED FURNACE

NOTE TO INSTALLER:
THIS MANUAL MUST BE LEFT WITH THE
EQUIPTMENT USER. 

®

• • • • •

• • • • •

• • • • •

U L T R A   H

I G H   E F F I

C I E N C Y

G A S   F U R

N A N C E

®

 

Summary of Contents for Weathermaker 9200











Reviews: