Carrier UC Open XP Installation And Startup Manual Download Page 13 | Manualshive

Page: 13 / 44

Carrier UC Open XP Installation And Startup Manual Download Page 13

UC Open XP/UC Open XP IO

9

4

Open the

Properties

page >

Equipment

tab to configure the controller. Each configuration parameter on

the

Properties

page >

Equipment

tab is explained in detail under the corresponding section. For

additional information on the operation of the equipment, consult the Sequence of Operation, which is

created in ApplicationBuilder, and the relevant

Installation and Start-up Guide

.

5

Check out and commission the equipment.

To mount the UC Open XP

When you handle the UC Open XP:
•   Do not contaminate the printed circuit board with fingerprints, moisture, or any foreign material.
•   Do not touch components or leads.
•   Handle the board by its edges.
•   Isolate from high voltage or electrostatic discharge.
•   Ensure that you are properly grounded.

Screw the UC Open XP into an enclosed panel using the mounting slots on the cover plate. Leave about 2 in.

(5 cm) on each side of the controller for wiring.
Mounting hole dimensions 4" (width) by 11.4" (height).

«
...
11
12
13
14
15
...
»

Summary of Contents for UC Open XP













































Reviews:

No comments