Carrier TruVu TV-MPCXP1628-NR Installation And Startup Manual Download

Page: 36 / 94

Wiring devices to the TV-MPCXP1628-NR's Rnet port

TruVu™ MPC Controller (

part no. TV-MPCXP1628-NR)

Installation and Start-up Guide

You can wire the following devices to the TV-MPCXP1628-NR's Rnet port in a daisy-chain configuration:

•

ZS sensors

•

Wireless Adapter that communicates with wireless sensors

•

Equipment Touch

•

TruVu™ ET Display

See the device's I

nstallation and Start-

up Guide for complete wiring instructions.

NOTES

•

ZS sensors, a Wireless Adapter, and an Equipment Touch can share the same Rnet.

•

The Rnet communicates at a rate of 115 kbps.

Wiring devices to the TV-MPCXP1628-NR's Rnet port

Summary of Contents for TruVu TV-MPCXP1628-NR































































































Search results

Summary of Contents for TruVu TV-MPCXP1628-NR

Reviews:

Related manuals for TruVu TV-MPCXP1628-NR

Brands by name

Popular brands

Carrier TruVu TV-MPCXP1628-NR, Installation And Startup Manual

Search results

Summary of Contents for TruVu TV-MPCXP1628-NR

Reviews:

Related manuals for TruVu TV-MPCXP1628-NR

Brands by name

Popular brands