Carrier PG95ESU User Manual Download

Page: 27 / 58

PG95ESU: Installation, Start-up, Operating and Service Maintenance Instructions

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

Alternate Power Supplies

This furnace is designed to operate on utility generated power which has

a smooth sinusoidal waveform. If the furnace is to be operated on a

generator or other alternate power supply, the alternate power supply

must produce a smooth sinusoidal waveform for compatibility with the

furnace electronics. The alternate power supply must generate the same

voltage, phase, and frequency (Hz) (

Table 13

) or the furnace rating plate.

Power from an alternate power supply that

is non-sinusoidal may

damage the furnace electronics

or cause erratic operation.

Contact the alternate power supply manufacturer for specifications and

details.

A190079

Fig. 40 – Typical Single-Stage Wiring Diagram

A190409

Fig. 41 – Example of Single Stage Furnace Control

115-V FIELD-

SUPPLIED

DISCONNECT

AUXILIARY
J-BOX

24-V

TERMINAL

BLOCK

THREE-WIRE

HEATING-ONLY

FIVE WIRE

NOTE 1

NOTE 2

FIELD-SUPPLIED
DISCONNECT

CONDENSING
UNIT

TWO
WIRE

FURNACE

C
O
N

R
O

COM

GND

FIELD 24-V WIRING
FIELD 115-, 208/230-, 460-V WIRING
FACTORY 24-V WIRING
FACTORY 115-V WIRING

208/230- OR
460-V
THREE
PHASE

208/230-V
SINGLE
PHASE

BLOWER DOOR SWITCH

WHT

BLK

WHT

BLK

NOTES:

Connect Y-terminal in furnace as shown for proper blower operation.
Some thermostats require a "C" terminal connection as shown.
If any of the original wire, as supplied, must be replaced, use
same type or equivalent wire.

GND

THERMOSTAT
TERMINALS

1.
2.
3.

24-V THERMOSTAT

TERMINALS

PL2

–

(115-VAC) HOT SURFACE IGNITER &
INDUCER MOTOR CONNECTOR

(L2) NEUTRAL

CONNECTIONS

115-VAC (BL) BLOWER MOTOR LINE

VOLTAGE CONNECTION

EAC-1 TERMINAL

(115-VAC EAC + HUM 1.0 AMP MAX.)

PL1

–

LOW VOLTAGE MAIN HARNESS

CONNECTOR plus INDUCER PWM

TRANSFORMER 24-VAC

CONNECTIONS

3-AMP FUSE

STATUS LED LIGHT

HEAT OFF-DELAY

MODEL PLUG
CONNECTOR

HUMIDIFIER TERMINAL

(24-VAC 0.5 AMP MAX.)

BOARD PART NUMBER

LOCATION

COOLING SPEED

TAP

HEATING SPEED

TAP

115-VAC (PR) TRANSFORMER

PRIMARY

J2 DEFEAT

JUMPER

TEST/TWIN

J1 HEAT OFF-DELAY

JUMPER SELECT

HUM 115-VAC TERMINAL

(115-VAC EAC + HUM 1.0 AMP MAX.)

FACTORY RUN TEST PORT

(FACTORY ONLY)

PROGRAMMING FLASH PORTS

(FACTORY ONLY)

115-VAC (L1) LINE VOLTAGE

CONNECTION

FAN SPEED TAP

PL3 - PRESSURE

TRANSDUCER INPUT

PL4

HUM

115VAC

SPARE UNUSED

TAPS

Summary of Contents for PG95ESU



























































Search results

Summary of Contents for PG95ESU

Reviews:

Related manuals for PG95ESU

Brands by name

Popular brands

Carrier PG95ESU, User Manual

Search results

Summary of Contents for PG95ESU

Reviews:

Related manuals for PG95ESU

Brands by name

Popular brands