Carrier N92ESN Installation, Start-Up, Operating And Service And Maintenance Instructions Download

Page: 1 / 66

Installation, Start-up, Operating and

Service and Maintenance Instructions

NOTE:

Read the entire instruction manual before starting the

installation.

TABLE OF CONTENTS

REQUIRED NOTICE FOR MASSACHUSETTS INSTALLATIONS

IMPORTANT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

SAFETY CONSIDERATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Table 1 – Minimum Clearances to Combustible Materials for All Units

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Table 2 – Loose Parts Bag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

CODES AND STANDARDS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

ELECTROSTATIC DISCHARGE (ESD) PRECAUTIONS PROCE

DURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

LOCATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

AIR FOR COMBUSTION AND VENTILATION . . . . . . . . . . . . . . 8

Table 3 – Minimum Free Area Required for Each Combustion Air

Opening or Duct to Outdoors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Table 4 – Minimum Space Volumes for 100% Combustion, Ventila

tion and Dilution Air from Outdoors . . . . . . . . . . . . . . . . . . . . . . . 9

CONDENSATE TRAP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

CONDENSATE DRAIN CONNECTION . . . . . . . . . . . . . . . . . . . . 12

INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Table 5 – Opening Dimensions - In. (mm) . . . . . . . . . . . . . . . . . 17

Table 6 – Filter Media Pressure Drop (Clean) Versus Airflow - In.

W.C. (Pa) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Table 7 – Filter Media Pressure Drop (Clean) Versus Face Velocity-

In. W.C. (Pa) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Table 8 – Air Filter Selection and Duct Sizing - In. (mm) . . . . . 20

AIR DUCTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

GAS PIPING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Table 9 – Maximum Capacity of Pipe . . . . . . . . . . . . . . . . . . . . . 22

ELECTRICAL CONNECTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Table 10 – Electrical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

VENTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Table 11 – Vent Termination Kit for Direct Vent (2-pipe) Systems28

Table 12 – Approved Combustion-Air and Vent Pipe, Fitting and Ce

ment Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Table 13 – Maximum Equivalent Vent Length . . . . . . . . . . . . . . 39

Table 14 – Deductions from Maximum Equivalent Vent Length - Ft.

(M) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Table 15 – Maximum Allowable Exposed Vent Lengths in Uncondi

tioned Space Table - Ft. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Table 16 – Hanger Spacing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

START-UP, ADJUSTMENT, AND SAFETY CHECK . . . . . . . . . 47

Table 17 – Altitude Derate Multiplier for U.S.A. . . . . . . . . . . . . 49

Table 18 – Gas Rate (CU ft./hr). . . . . . . . . . . . . . . . . . . . . . . . . . 50

Table 19 – Orifice Size and Manifold Pressure (in. w.c.) for Gas Input

Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Table 20 – Blower Off Delay Jumper Positions . . . . . . . . . . . . . 52

Table 21 – Air Delivery - CFM (With Filter) . . . . . . . . . . . . . . . 52

SERVICE AND MAINTENANCE PROCEDURES. . . . . . . . . . . . 54

WINTERIZATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

SEQUENCE OF OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

PARTS REPLACEMENT INFORMATION GUIDE . . . . . . . . . . . 66

MODEL NOMENCLATURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

A200326

Most states in the USA and jurisdictions in Canada have laws that

require the use of Carbon Monoxide (CO) alarms with fuel burning

products. Examples of fuel burning products are furnaces, boilers, space

heaters, generators, water heaters, stoves/ranges, clothes dryers,

fireplaces, incinerators, automobiles, and other internal combustion

engines. Even if there are no laws in your jurisdiction requiring a CO

Alarm, it’s highly recommended that whenever any fuel burning product

is used in or around the home or business that the dwelling be equipped

with a CO Alarm(s). The Consumer Product Safety Commission

recommends the use of CO Alarm(s). The CO Alarm(s) must be

installed, operated, and maintained according to the CO Alarm

manufacturer’s instructions. For more information about Carbon

Monoxide, local laws, or to purchase a CO Alarm online, please visit the

following website. https://www.kidde.com.

Portions of the text and tables are reprinted from NFPA 54/ANSI Z223.1E, with permission of National Fire Protection Association, Quincy, MA

02269 and American Gas Association, Washington DC 20001. This reprinted material is not the complete and official position of the NFPA or ANSI

on the referenced subject, which is represented only by the standard in its entirety.

N92ESN

Single-Stage, 35-in. (889 mm) Tall, 4-Way Multipoise

High Efficiency Condensing Gas Furnace

WARNING

CARBON MONOXIDE POISONING HAZARD

Failure to follow this warning could result in personal injury and/or

death.

Carbon Monoxide (CO) is a colorless, odorless, and tasteless poisonous

gas that can be fatal when inhaled. Follow all installation, maintenance,

and service instructions. See additional information below regarding

the installation of a CO Alarm.

Use of the AHRI Certified TM Mark indicates
a manufacturer's participation in the program.
For verification of certification for individual
products, go to www.ahridirectory.org .

Summary of Contents for N92ESN



































































Search results

Summary of Contents for N92ESN

Reviews:

Related manuals for N92ESN

Brands by name

Popular brands

Carrier N92ESN, Installation, Start-Up, Operating And Service And Maintenance Instructions

Search results

Summary of Contents for N92ESN

Reviews:

Related manuals for N92ESN

Brands by name

Popular brands