background image

Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.

Catalog No. 04-53480393-01

Printed in U.S.A.

Form IIK-CRECOMZR87-01

Pg 1 

3-22

Replaces: NEW

Installation Instructions

Part No. CRECOMZR087A00

* The EconoMi$er2 assembly does not include an economizer controller.

SAFETY CONSIDERATIONS

Installation of this accessory can be hazardous due to system
pressures, electrical components, and equipment location (such as
a roof or elevated structure). Only trained, qualified installers and
service technicians should install, start-up, and service this
equipment. 
When installing this accessory, observe precautions in the
literature, labels attached to the equipment, and any other safety
precautions that apply:

Follow all safety codes

Wear safety glasses and work gloves

Use care in handling and installing this accessory

It is important to recognize safety information. This is the safety-
alert symbol: 

. When you see this symbol on the unit and in

instructions or manuals, be alert to the potential for personal
injury.
Understand the signal words DANGER, WARNING,
CAUTION, and NOTE. These words are used with the safety-
alert symbol. DANGER identifies the most serious hazards which

will

 result in severe personal injury or death. WARNING signifies

hazards which 

could

 result in personal injury or death. CAUTION

is used to identify unsafe practices, which 

may

 result in minor

personal injury or product and property damage. NOTE is used to
highlight suggestions which 

will

 result in enhanced installation,

reliability, or operation.

 GENERAL

The EconoMi$er2 system utilizes the latest technology available
for integrating the use of free cooling with mechanical cooling for
rooftop units.
This system utilizes gear-drive technology with a direct mount
spring return actuator that will close upon loss of power. The
EconoMi$er2 system comes standard with an outdoor air
temperature sensor. Field-installed CO

2

 sensors are available.

Separate barometric relief dampers provide natural building
pressurization control. An optional power exhaust system is
available for applications requiring even greater exhaust
capabilities.
EconoMi$er2 accessories require a 4 to 20 mA actuator signal
control. These accessories do not include a controller. The
EconoMi$er2 actuator is operated by a 4 to 20 mA signal from an
existing field-supplied DDC controller. See Table 1 for package
contents and Fig. 1 for EconoMi$er2 component locations. See
Table 2 for accessories list and Table 3 for sensor usage.

ACCESSORIES AND COMPLIANCE

Accessories List

The EconoMi$er2 system has several field-installed accessories
available to optimize performance. Refer to Table 2 for authorized
parts and power exhaust descriptions.

Table 1 — Package Contents

PART NUMBER

QTY

CONTENTS

CRECOMZR087A00

1

Hood Assembly

1

Filter Access Door

1

Aluminum Filter

18

Screws

1

EconoMi$er2 Assembly*

1

Barometric Relief Hood 

Assembly

1

Hood O/A Panel 

1

O/A Panel Access Door

1

O/A Small Blank Off

1

O/A Large Blank Off

1

R/A Small Blank Off

1

R/A Large Blank Off

IMPORTANT: Read these instructions completely before
attempting to install the horizontal EconoMi$er2 accessory.

WARNING

ELECTRICAL SHOCK HAZARD
Failure to follow this warning could cause personal injury and/
or death.
Disconnect power supply and install lockout tag before
attempting to install the accessory.

Table 2 — EconoMi$er2 Field-Installed Accessories

PART NUMBER

DESCRIPTION

CRPWREXH028A01

Small And Large Cabinet Power 
Exhaust 208-230v 1Ph

CRPWREXH029A01

Small And Large Cabinet Power 
Exhaust 460-v 3Ph

33ZCT55SPT

Return Air Dry Bulb

CRHUMDSN001B00

or

33CSENTHSW

Outdoor Air Enthalpy Sensor

CRHUMDSN001B00

or

33CSENTSEN

Return Air Enthalpy Sensor

33ZCSENCO2

CO

2

 Room Sensor

33ZCASPCO2

Aspirator Box For Duct Mount 
CO

2

 Sensor

33ZCT55CO2

Space Temperature And CO

2

 

Room Sensor With Override

33CZT56CO2

Space Temperature And CO

2

 

Room Sensor With Override 
And Setpoint

Small Rooftop Units

Accessory Horizontal Ultra-Low Leak

EconoMi$er2

7-1/2 to 12-1/2 Tons

Summary of Contents for EconoMiser2 CRECOMZR087A00









Reviews: