manualshive.com logo in svg

Carrier BACview, Installation And User Manual

Share
Download
Carrier BACview Installation And User Manual Download Page 21

 

The BACview®6 device

 

 

 

 
 

BACview® 

 

CARRIER CORPORATION ©2021   

Installation and User Guide 

 

All rights reserved 

 

17 

 

Wiring 2 BACview®6 devices to the Rnet 

Two BAC

view

®

6 

devices on an Rnet display the same screen. 

The first BAC

view

®

6 

device on an Rnet is powered by the controller. You must provide an external power supply for 

a second BAC

view

®

6 

device. 

 

The BAC

view

®

6

 device is powered by a Class 2 power source. Properly isolate the BAC

view

®

6 

device from non-

Class 2 circuits in the same control panel. 

  

 

  

Set the address of each BAC

view

®

6

 device by putting one's jumper in the top position and the other's jumper in 

the bottom position.  

 

 

 

 

Using the BACview®6 device 

The instructions to use the BAC

view

®

6

 device are the same as those for the BAC

view

®

6

 Handheld device. See 

Using the BACview®

6

 Handheld device

 (page 4). 

  

NOTE

  For information on the BAC

view

®

 

screens for a specific controller, see the controller's 

Installation and 

Startup Guide

. For information on system screens that are common to most controllers, see 

BACview® system 

screens

 (page 18). 

 

 

 

Summary of Contents for BACview


































Reviews:

No comments

Brands by name

Popular brands

Load more brands