background image

49

• 

Remove the dust and clean the interior of the control 

boxes, if required.

• 

Check the presence and the condition of the electrical 

protection devices.

• 

Check the correct operation of all heaters.

• 

Replace the fuses every 3 years or every 15000 hours 

(age-hardening).

• 

Replace the control box cooling fans used with option 
22 (with designation EF22_) every five years.

• 

Check the height of the anti-vibration mountings 

(located between the compressor rails and the unit 
chassis) after 5 years of operation, and then each year. 
When the total minimum height of the mountings is 
less than 25 mm replace the mountings.

• 

Check the water connections.

• 

Purge the water circuit.

• 

Clean the water filter.

• 

Fully clean the condensers with a low-pressure jet and 

a bio-degradable cleaner (counter-current cleaning - 
see chapter 13.6.2 - “Level 2”).

• 

Replace the stuffing box packing of the pump after 

10000 hours of operation.

• 

Check the unit operating parameters and compare 

them with previous values.

• 

Keep and maintain a maintenance sheet, attached to 

each HVAC unit.

• 

Check the correct operation of the capacitor (power 

factor correction option 231).

All these operations require strict observation of adequate 
safety measures: Individual protection garments, compliance 
with all industry regulations, compliance with applicable 
local regulations and using common sense. 

13.3 - Level 3 (or higher) maintenance

NOTE: Any deviation or non-observation of these mainte-
nance criteria will render the guarantee conditions for the 
HVAC unit null and void, and the manufacturer, Carrier 
SCS will no longer be held responsible.

The maintenance at this level requires specific skills/

approval/tools and know-how and only the manufacturer, 
his representative or authorised agent are permitted to 
carry out these operations. These maintenance operations 
concern for example:

• 

A major component replacement (compressor, 

evapo-rator)

• 

Any intervention on the refrigerant circuit (handling 

refrigerant)

• 

Changing of parameters set at the factory (application 

change)

• 

Removal or dismantling of the HVAC unit

• 

Any intervention due to a missed established mainte-

nance operation

• 

Any intervention covered by the warranty.

13 - STANDARD MAINTENANCE

Air conditioning equipment must be maintained by profes-
sional technicians, whilst routine checks can be carried out 
locally by specialised technicians. See the standard 
EN 378-4.

Simple preventive maintenance will allow you to get the 
best performance from your HVAC unit:

• 

Improved cooling performance

• 

Reduced power consumption

• 

Prevention of accidental component failure

• 

Prevention of major time-consuming and costly 

inter-ventions

• 

Protection of the environment.

There are five maintenance levels for HVAC units, as 
defined by the AFNOR X60-010 standard.

13.1 - Level 1 maintenance

See note “Any deviation or non-observation ...” in chapter 
13.3 - “Level 3 (or higher) maintenance”. Simple 
procedure can be carried out by the user:

• 

Visual inspection for oil traces (sign of a refrigerant 

leak)

• 

Air heat exchanger (condenser) cleaning - see chapter  

13.6.1 - “Level 1”.

• 

Check for removed protection devices, and badly 

closed doors/covers

• 

Check the unit alarm report when the unit does not 

work. Refer to the 30XA/30XAS/30XW Touch Pilot 
control manual for a more detailed explanation.

 
General visual inspection for any signs of deterioration.
 

13.2 - Level 2 maintenance

See note “Any deviation or non-observation ...” in the ext 

column. This level requires specific know-how in the 
electrical, hydronic and mechanical fields. It is possible that 

these skills are avail-able locally: Existence of a 
maintenance service, industrial site, specialised 
subcontractor. In these cases, the following maintenance 
operations are recommended.

Carry out all level 1 operations, then:  

• 

At least once a year tighten the power circuit 

electrical connections (see table 13.4).

• 

Check and re-tighten all control/command 

connections, if required (see table 13.4).

• 

Check the differential switches for correct operation 

every 6 months (free-cooling option 118A).

Summary of Contents for Aquaforce 30XA Series

























































Reviews: