Carrier AquaEdge 19XR series Start-Up, Operation And Maintenance Instructions Manual Download

Page: 99 / 212

TROUBLESHOOTING GUIDE

Overview —

The PIC II has many features to help the op-

erator and technician troubleshoot a 19XR chiller.
• The ICVC shows the chiller’s actual operating condi-

tions and can be viewed while the unit is running.

• The ICVC default screen freezes when an alarm occurs.

The freeze enables the operator to view the chiller condi-

tions at the time of alarm. The STATUS screens continue

to show current information. Once all alarms have been

cleared (by correcting the problems and pressing

the

softkey), the ICVC default screen returns to

normal operation.

• The CONTROL ALGORITHM STATUS screens (which

include the CAPACITY, OVERRIDE, SURGPREV,

LL_MAINT, ISM_HIST, LOADSHED, CUR_ALARM,

WSMDEFME, and OCCDEFCM screens) display infor-

mation that helps to diagnose problems with chilled

water temperature control, chilled water temperature

control overrides, hot gas bypass, surge algorithm status,

and time schedule operation.

• The control test feature facilitates the proper operation

and test of temperature sensors, pressure transducers, the

guide vane actuator, diffuser actuator (if equipped), oil

pump, water pumps, tower control, and other on/off out-

puts while the compressor is stopped. It also has the abil-

ity to lock off the compressor and turn on water pumps

for pumpout operation. The ICVC shows the tempera-

tures and pressures required during these operations.

• From other SERVICE tables, the operator/technician can

access configured items, such as chilled water resets,

override set points, etc.

• If an operating fault is detected, an alarm message is gen-

erated and displayed on the ICVC default screen. A more

detailed message — along with a diagnostic message —

is also stored into the ALARM HISTORY table.

• Review the ALERT HISTORY table to view other less

critical events which may have occurred. Compare tim-

ing of relevant events and alarms.

Checking Display Messages —

The first area to

check when troubleshooting the 19XR is the ICVC display. If

the alarm light is flashing, check the chiller primary and sec-

ondary message lines on the ICVC default screen (Fig. 17).

These messages will indicate where the fault is occurring.

These messages contain the alarm message with a specified

code. This code or state appears with each alarm and alert mes-

sage. The ALARM and ALERT HISTORY tables on the ICVC

SERVICE menu also contain an alarm or alert message to fur-

ther expand on the alarm or alert. For a complete list of possi-

ble alarm messages, see Table 16. If the alarm light starts to

flash while accessing a menu screen, press the

softkey to

return to the default screen to read the alarm message. The

STATUS screen can also be accessed to determine where an

alarm exists.

A “C” to the right of a parameter’s value means that there is

a communications fault on that channel.

Checking Temperature Sensors —

All tempera-

ture sensors are thermistor-type sensors. This means that the re-

sistance of the sensor varies with temperature. All sensors have

the same resistance characteristics. If the controls are on, deter-

mine sensor temperature by measuring voltage drop; if the con-

trols are powered off, determine sensor temperature by measur-

ing resistance. Compare the readings to the values listed in

Tables 17A and 17B.
RESISTANCE CHECK — Turn off the control power and,

from the module, disconnect the terminal plug of the sensor in

question. With a digital ohmmeter, measure sensor resistance

between receptacles as designated by the wiring diagram. The

resistance and corresponding temperature are listed in

Tables 17A and 17B. Check the resistance of both wires to

ground. This resistance should be infinite.
VOLTAGE DROP — The voltage drop across any energized

sensor can be measured with a digital voltmeter while the con-

trol is energized. Table 17A or 17B lists the relationship be-

tween temperature and sensor voltage drop (volts dc measured

across the energized sensor). Exercise care when measuring

voltage to prevent damage to the sensor leads, connector plugs,

and modules. Sensors should also be checked at the sensor

plugs.

RESET

CAUTION

Relieve all refrigerant pressure or drain the water before

removing any thermowell threaded into the refrigerant

pressure boundary. Failure to do so could result in personal

injury and equipment damage.

EXIT

continued on page 116.

Summary of Contents for AquaEdge 19XR series





















































































































































































































Search results

Summary of Contents for AquaEdge 19XR series

Reviews:

Related manuals for AquaEdge 19XR series

Brands by name

Popular brands

Carrier AquaEdge 19XR series, Start-Up, Operation And Maintenance Instructions Manual

Search results

Summary of Contents for AquaEdge 19XR series

Reviews:

Related manuals for AquaEdge 19XR series

Brands by name

Popular brands