Carrier 339282-769 thru 772, Quick Start Manual

Page: 1 / 4

OUTER DOOR (BASE) SERVICE KIT
NOTE: Read the entire instruction manual before starting the
installation.
BOOKLET KIT NUMBERS
339282-769 thru 772
339283-775 thru 778
339286-769 thru 772
SAFETY CONSIDERATIONS
Improper installation, adjustment, alteration, service, maintenance, or
use can cause explosion, fire, electrical shock, or other conditions which
may cause death, personal injury, or property damage. Consult a
qualified installer, service agency, or your distributor or branch for
information or assistance. The qualified installer or agency must use
factory-authorized kits or accessories when modifying this product.
Refer to the individual instructions packaged with the kits or accessories
when installing.
Follow all safety codes. Wear safety glasses, protective clothing, and
work gloves. Have a fire extinguisher available. Read these instructions
thoroughly and follow all warnings or cautions included in literature and
attached to the unit. Consult local building codes, the current editions of
the National Fuel Gas Code (NFGC) NFPA 54/ANSI Z223.1 and the
National Electrical Code (NEC) NFPA 70.
In Canada, refer to the current editions of the National Standards of
Canada CAN/CSA-B149.1 and .2 Natural Gas and Propane Installation
Codes, and Canadian Electrical Code CSA C22.1.
Recognize safety information. This is the safety-alert symbol . When
you see this symbol on the unit and in instructions or manuals, be alert to
the potential for personal injury.
Understand the signal words DANGER, WARNING, and CAUTION.
These words are used with the safety-alert symbol. DANGER identifies
the most serious hazards which will result in severe personal injury or
death. WARNING signifies hazards which could result in personal
injury or death. CAUTION is used to identify unsafe practices which
may result in minor personal injury or product and property damage.
NOTE is used to highlight suggestions which will result in enhanced
installation, reliability, or operation.
INTRODUCTION
This instruction covers the outer door installation on 35 in. (889 mm) tall
condensing gas furnaces.
The door should be replaced when it is missing or severely damaged.
Minor damage or scrapes may be repaired and the finish repaired with
touch-up paint.
DESCRIPTION AND USAGE
The door replacement kit can be utilized to restore units having missing
door or doors severely damaged beyond repair. This kit contains the
following items: Outer Door assembly with latches and model specific
Instruction Booklets matched to different types of furnaces.
The Instruction Booklets are matched to specific model families as
shown in Table 1 . Match the QUICK REFERENCE NUMBER and affix
new booklet to the new door assembly.
L12F007
Fig. 1 – Quick Reference Number
Booklet Service Kit for Condensing Gas Furnace
Use with 35 in. (889 mm)
High Efficiency Gas Furnace
WARNING
!
FIRE, EXPLOSION, ELECTRICAL SHOCK
HAZARD
Failure to follow this warning could result in personal injury, death
and/or property damage.
The ability to properly perform maintenance on this equipment requires
certain knowledge, mechanical skills, tools, and equipment. If you do
not possess these, do not attempt to perform any maintenance on this
equipment other than those procedures recommended in the Home
Owner’s Information Manual.
WARNING
!
FIRE, EXPLOSION, ELECTRICAL SHOCK AND
CARBON MONOXIDE POISONING HAZARD
Failure to follow this warning could result in personal injury, death
and/or property damage.
Improper installation, adjustment, alteration, service, maintenance, or
use can cause carbon monoxide poisoning, explosion, fire, electrical
shock, other conditions, which could result in personal injury or death.
Consult your distributor or branch for information or assistance. The
qualified installer or agency must use only factory-authorized kits or
accessories when servicing this product.
WARNING
!
ELECTRICAL SHOCK, FIRE OR EXPLOSION HAZARD
Failure to follow this warning could result in personal injury or death,
or property damage.
Before installing, modifying, or servicing system, main electrical
disconnect switch must be in the OFF position and install a lockout tag.
There may be more than one disconnect switch. Lock out and tag
switch with a suitable warning label. Verify proper operation after
servicing.