24ACC6
Comfort
t
Series Air Conditioner
1 1/2 To 5 Nominal Tons
Wiring Diagrams
334024-101 REV. B
CONNECTION DIAGRAM
COMP
OFM
S
C
R
BLU
BRN
BLK
YEL
BLK
YEL
RED or BLK
208/230 1Ø
POWER
SUPPLY
EQUIP GND
L1
L2
BLU
CAP
H
C
F
YEL
*ST
+t
BLU
YEL
YEL
*SC
*CHS
*SR
(NOTE #8)
1
2
5
*CH
BLK
BLK
or
RED
BLK
BRN
(NOTE #9)
BLK
CONDENSING UNIT CHARGING INSTRUCTIONS
For use with units using R-410A refrigerant
INDOOR BLOWER MOTOR
EXTERNAL
POWER
SUPPLY
24 V
(NOTE #3)
INDOOR THERMOSTAT (NOTE #6)
R
G
Y
*LLS
BLK
BLK
C
R
VIO
BRN/YEL
*LPS
*HPS
LOGIC
T1
*CTD
BLK
BLU/PNK
T3
T2
NOTES:
1. Symbols are electrical
representation only.
2. Compressor and fan motor
furnished with inherent thermal
protection.
3. To be wired in accordance with
National Electric N.E.C.
and local codes.
4. N.E.C. class 2, 24V circuit, min.
40 VA required, 60 VA on units
installed with LLS.
5. Use copper conductors only.
Use conductors suitable for at
least 75ºC (167ºF).
6. Connection for typical cooling
only thermostat. For other
arrangements see installation
instructions.
7. If indoor section has a
transformer with a grounded
secondary, connect the
grounded side to the BRN/YEL
lead.
8. When start relay and start
capacitor are installed, start
thermistor is not used.
9. CH not used on all units.
10. If any of the original wire, as
supplied must be replaced,
use the same or equivalent
wire.
11. Check all electrical
connections inside control
box for tightness.
12. Do not attempt to operate unit
until service valves have
been opened.
13. Do not rapid cycle
compressor.
Compressor must be off 3
minutes to allow
pressures to equalize
between high and low
side before starting.
* MAY BE FACTORY INSTALLED
LEGEND
FACTORY POWER WIRING
FACTORY CONTROL WIRING
FIELD CONTROL WIRING
FIELD POWER WIRING
COMPONENT CONNECTION
FIELD SPLICE
JUNCTION
PLUG RECEPTACLE
CONT
CAP
*CH
*CHS
COMP
*CTD
*DTS
*HPS
IFR
*LLS
*LPS
OFM
*SC
*SR
*ST
CONTACTOR
CAPACITOR (DUAL RUN)
CRANKCASE HEATER
CRANKCASE HEATER SWITCH
COMPRESSOR
COMPRESSOR TIME DELAY
DISCHARGE TEMP SWITCH
HIGH PRESSURE SWITCH
INDOOR FAN RELAY
LIQ LINE SOLENOID VALVE
LOW PRESSURE SWITCH
OUTDOOR FAN MOTOR
START CAPICATOR
START RELAY
START THERMISTOR
CAUTION
1. Compressor damage may occur if system is
over charged.
2. This unit is factory charged with R-410A in
accordance with the amount shown on the
rating plate. The charge is adequate for most
systems using matched coils and tubing not
over 15 feet long. Check refrigerant charge
for maximum efficiency. See Product Data
Literature for required Indoor air Flow Rates
and for use of line lengths over 15 feet.
3. Relieve pressure and recover all refrigerant
before system repair or final disposal. Use all
service ports and open all flow-control devices,
including solenoid valves.
4. Never vent refrigerant to atmosphere. Use
approved recovery equipment.
SCHEMATIC DIAGRAM (LADDER FORM)
L1
*CH
EQUIP
GND
*SR
*SC
H
*ST
C
F
CAP
OFM
L2
5
2
1
*HPS
* CTD
*LLS
IFR
INDOOR THERMOSTAT
Y
G
R
C
R
EXTERNAL POWER SUPPLY 24 V
+
t
LOGIC
T1
T3
T2
CONT
COMP
S
C
R
*CHS
*LPS
CONT
11
21
23
23
11
21
CONT
CONT
23
23
YEL/ PNK
YEL/ PNK
BLU/PNK
COOLING ONLY
CHARGING PROCEDURE
1. Only use sub cooling charging method
when OD ambient is greater than 70ºF
and less than 100ºF, indoor temp is
greater than 70ºF and less than 80ºF,
and line set is less than 80 ft.
2. Operate unit a minimum of 15 minutes
before checking the charge.
3. Measure liquid service valve pressure
by attaching an accurate gauge to the
service port.
4. Measure the liquid line temperature by
attaching an accurate thermistor type
or electronic thermometer to the liquid
line near the outdoor coil.
5. Refer to unit rating plate for required
subcooling temperature.
6. Find the point where the required sub-
cooling temperature intersects the
measured liquid service valve pressure.
7. To obtain the required subcooling
temperature at specific liquid line
pressure, add refrigerant if liquid line
temperature is higher than indicated.
When adding refrigerant, charge in
liquid form using a flow restricting
device into suction service port.
Recover refrigerant if temperature is
lower. Allow a tolerance of +/- 3ºF.
REQUIRED LIQUID LINE TEMPERATURE
Required Subcooling
Temperature (ºF)
Liquid Pressure
at Service
Valve (psig)
6
8
10 12 14 16
251
259
266
274
283
291
299
308
317
326
335
345
354
364
374
76
74
72
70
68
78
76
74
72
70
80
78
76
74
72
82
80
78
76
74
84
82
80
78
76
86
84
82
80
78
88
86
84
82
80
90
88
86
84
82
92
90
88
86
84
94
92
90
88
86
96
94
92
90
88
98
96
94
92
90
100
98
96
94
92
102 100
98
96
94
104 102 100
98
96
384
395
406
416
427
439
450
462
474
106 104 102 100
98
108 106 104 102 100
110 108 106 104 102
112 110 108 106 104
114 112 110 108 106
116 114 112 110 108
118 116 114 112 110
120 118 116 114 112
122 120 118 116 114
78
80
82
84
86
88
90
92
94
96
98
100
102
104
106
108
110
112
114
116
118
120
122
124
Fig. 1 – Wiring Diagram — Model sizes 1--1/2 -- 5 tons, 208/230--1
