background image

7

ENG

Introduction

WTS +0300130EN rel. 1.0 - 05.09.2022

Dear Customer,

Thank you for choosing a CAREL reverse osmosis unit. CAREL reverse osmoses units are state of the art.

In order to operate your CAREL reverse osmosis unit safely, properly and efficiently, please read these operating 

instructions.

Only use the CAREL R.O. unit in faultless condition and for its intended use, being aware of safety and hazards, and 

observing all instructions in this manual.

If you have additional questions, please contact your expert dealer.

For all technical questions or spare parts orders, please be prepared to provide unit type and serial number (see name 

plate on the unit).

1.1  Typographic Distinctions

preceded by a bullet: general specifications

»

preceded by an arrow: Procedures for servicing or maintenance which should or must be performed in the indicated order

þ

installation step which must be checked off.

italics

Terms used with graphics or drawings

1.2  Documentation

Retention

Please retain these operating instructions in a secure, always accessible location. If the product is resold, turn the 

documentation over to the new operator. If the documentation is lost, please contact CAREL.

Versions in Other Languages

These operating instructions are available in several languages. If interested, please contact CAREL or your CAREL dealer.

1.3  Symbols in Use

Specific Symbols related to Safety Instructions

According to ANSI Z535.6 the following signal words are used within this document:

DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury.

WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

NOTICE is used to address practices not related to physical injury.

 

1.3.1  General Symbols

 

Notice: 

This symbol is used whenever a situation requires special attention beyond the scope of safety instructions.

1.4  Intended Use

CAREL reverse osmosis unit is used to produce fully demineralized water.  

It may only be used in accordance with its intended purpose.

 

Notice

:

•   Intended use also includes compliance with the assembly, disassembly and reassembly, commissioning, operating and main-

tenance conditions and disposal measures prescribed by us.

•   Only qualified and authorized personnel may work on and with the system. Persons who carry out transport or work on 

and with the system must have read the relevant parts of the operating instructions and in particular the chapter “Safety 
instructions”. In addition, the personnel must be informed by the operator of any hazards that may exist. Leave a copy of the 
operating manual at the place of use of the unit.

•  The installation of additional equipment is only permitted with the written approval of the manufacturer.

Use of the system

•   The system is intended for operation (with use of feed water in the drinking water sector) of humidification systems.
•   The limit and guide values as per the regulations enforced in the installation country must be taken into account.
•   Frost protection and protection against excessive moisture must be ensured
•   The permitted surrounding temperature is between 5° C and 40° C
•   The use of a system separator according to DIN 1988, part 4 and DIN EN 1717 is obligatory.

1.  INTRODUCTION

Summary of Contents for Compact ROC 140





























































Reviews: