®
REMOTE START with KEYLESS ENTRY SYSTEM
Quick Reference Install Guide
FOR PROFESSIONAL INSTALLATION ONLY!
If you are not proficient in the installation of this product or would like a full ver-
sion of the installation manual, please visit our web site @www.magnadyne.com
Receiver/Control
Center(RCC)
Pink: (+) Ignition 1 Input/Output
Red: +12V Input
Red: +12V Input
Red: +12V Battery Power
Brown: (-) Horn Output
16 PIN
(see chart)
Black: System Main Ground
White: Parking Light Relay Output
Blue: - Negative Door Unlock Output
Green: - Negative Door Lock Output
White: Parking Light Relay Power Input
Violet: Starter Output
Pink/White: Ignition 2 Output
Orange: Accessory Output
Fortin or iDatalink
Bypass Module
30A
30A
15A
10A
16
5
6
7
8
9
10
11
15 14 13
4 3 2
12
1
16 Pin Accessory Harness Wiring:
Pin
Color
Function
Pin
Color
Function
1
Green/White
(-) Factory Alarm Re-Arm Output
9
Orange
(-) GND When Armed/Lock
2
Gray
(-) Hood Pin Safety Input
10
Red/White
(-) Channel 3 Output (Trunk)
3
Black/White
(-) Parking Brake Input
11
Lt. Purple/Yellow
(-) Starter Output
4
Open
None
12
Lt. Green/Black
(-) Factory Alarm Disarm Output
5
Brown
(+) Vehicle Brake Safety Input
13
Blue/White
(-) 2nd Status/Defrost Output
6
White/Blue
External Activation Input
14
Dk. Blue
(-) Status Output
7
Yellow
(+) Ignition Output (to alarm)
15
Orange/White
(-) Accessory Output
8
Lt. Violet/White
Tach Input (AC)
16
Pink
(-) Ignition Output
Mounting the Receiver/Control Center (RCC):
1. Choose a location on the upper or sides of the vehicle windshield.
A higher location is best.
2. Remove the backing liner from the mounting tape on the backside of the
RCC and stick it to the windshield glass.
3. Route the RCC cable to the location of the control module.
Programming System Features:
All CARBINE remote start systems have a menu of features that can
be programmed to suit the installation requirements of any vehicle.
These features can be set by using the RCC button Feature Programming
procedure or by Windows PC programming and the CARBINE web app.
Feature Programming by RCC Button
1. Open the drivers door.
2. Turn the ignition key ON then OFF.
3. Within 5 seconds, press and hold the RCC button to select the menu.
- A single chirp and LED flash indicates Menu #1.
- Hold the button longer for two chirps and two LED flashes.
You are in menu #2.
4. When the desired menu is reached, release the RCC button.
5. Within 5 seconds, press and release the RCC button the number of
times corresponding to the feature you want to change then press and
hold the button once more to lock the feature. Chirps and LED flashes
will confirm the feature chosen. Release the button. Use the buttons on
the CARBINE remote to adjust the feature.
6. For features with only two options, the = 1 Chirp setting,
while the = 2 Chirp setting.
7. For features with more than two settings, the button selects the
settings in ascending order. Horn chirps indicate which option is selected.
8. Turn on the igntion key to exit Feature Programming.
Menu #1
(Default in Bold)
Item Feature
Chirps
1
2
3
4
5
6
7
8
9
1
Data Protocol
ADS
Fortin
2
Ignition
Locking
Off
On
3
Ignition
Unlock
Off
On
4
Panic with
Ignition On
Off
On
5
Door Lock
Pulse
0.8 sec.
3.5 sec. 0.4 sec.
6
Double Pulse
Lock
Off
(Single)
On
(Double
7
Double Pulse
Unlock
Off
(Single)
On
(Double)
8
Factory Alarm
Disarm Pulse
Single
Double
9
Factory Alarm
Disarm
With
Unlock
Before
Unlock
Remote
Start
Only
10
Horn Output
20 ms
30 ms
40 ms 50 ms Panic
Only
11
Comfort
Closure
Off
CC1
CC2
Menu #2
(Default in Bold)
Item Feature
Chirps
1
2
3
4
5
6
7
8
9
1
Transmission
Type
Automatic
Manual
2
Engine Checking
Mode
Wireless
Tach
Voltage
Wired
Tach
Off
3
Cranking Time
0.6 sec
0.8 sec 1.0 sec 1.2 sec 1.4 sec 1.6 sec 1.8 sec 2.0 sec 4.0 sec
4
Remote Start
Run Time
12 min
24 min
60 min
5
Anti-Grind
Output
On
Off
6
Diesel Start
Delay
Off
Timed
15 sec
Timed
30 sec
Timed
45 sec
7
ACC Output
During Diesel
Wait to Start
Off
On
8
2nd Ignition
Behavior
Ignition 1
ACC
9
Blue / White
Wire
Behavior
GND
When
Running
Rear
Defog
Latched
10 min
Rear
Defog
Pulse
10
External Trigger
Pulse Count
1 Pulse
2 Pulse 3 Pulse
11
Parking Light
Behavior
Constant
Flashing
12
Timer Mode Run
Time
12 min
3 min
6 min
9 min
Access another feature within the same menu
1. Press and release the RCC Button the number of times to advance from
the last feature programmed to the next feature to be programmed.
2. Press the RCC button and hold it.
3. Use the CARBINE remote and follow steps 5 or 6 above to adjust
the feature.
Access another menu
1. Press and hold the RCC Button
2. After 3 seconds, the system will advance to the next menu and conform
with chirps and LED flashes.
Exiting the feature program mode
1. Set the ignition key to ON. A long confirmation chirp will be hear if a
horn or siren is connected.
2. Automatic after 30 seconds with no input from the RCC button
(long chirp).
3. The RCC button has been press too many times (long chirp).
Feature Programming by PC/App
1. A windows computer with internet support is required. The APP supports
Windows 7 (sp1) thru Windows 10 (Apple/Mac computers are not supported)
2. The programming adaptor model #ALA-21P is required
3. Follow the instructions provided with the ALA-21P accessory.
