Canon VB-H43 Operation Manual Download Page 61

Page: 61 / 195

ting Page

All Videos

[Video Size Set]

Select the set of video sizes used by the camera. All

options in the [Video] menu and the size set that can be

selected in [Video Size] are determined by the set

selected here.

JPEG

(1) [Video Quality]

Select a desired video quality from 1 to 5 (5 levels) for

videos transmitted at each video size in JPEG.

Greater values have higher quality.

(2) [Video Quality: Digital PTZ]

Select a desired video quality from 1 to 5 (5 levels) for

Digital PTZ.

Greater values have higher quality.

(3) [Video

ize: video Transmission]

Select the size of the transmitted video. The video

sizes that can be selected depend on the [Video Size

Set] setting.

The default video size is selected if the video size is

not specified in each type of viewer.

(4) [Maximum Frame Rate: Video Transmission]

Limit the maximum transmission frame rate per

second to reduce the viewer load. The maximum is 30

frames/sec. Enter a value of between 0.1 and 30.0.

(5) [Video

ize: Upload / Memory card]

Select the size of video when using the upload

function (p. 66) or when recording to a memory card

(p. 84). The video sizes that can be selected depend

on the [Video Size Set] setting. Use [Event] > [Video

Record Action] (p. 71) to specify the destination of a

video recording (upload or memory card recording).

[Video] Setting Video Size, Quality and Frame Rate

The following can be set here.

• All Videos

Specify the set of video sizes used by the camera.

• JPEG

Set the video quality, size, maximum frame rate

and upload size in JPEG.

• H.264

Set the bit rate, video size and capture frame rate

in H.264.

• On-screen display

Set time, character string, etc. displayed over

images.

[Video

ize

et]

ystem

Aspect ratio

[1920x1080/960x540/480x270] 1080p

16:9

[1280x720/640x360/320x180]

720p

16:9

[1280x960/640x480/320x240]

4:3

[Video

ize

et]

ystem

Aspect ratio

[1280x720/640x360/320x180]

720p

16:9

[1280x960/640x480/320x240]

4:3

Important

• Changing the [Video Size Set] setting will disconnect all

connections and then change all the video sizes.

Consequently, users connected to the camera must
reconnect.

• If the [Video Size Set] selection is changed and you click

[Apply and Reboot], review the following settings and check

the operation.

- Privacy mask settings
-

View restriction settings

- Preset settings

- Intelligent function settings
-

Camera Angle Setting Tool

Summary of Contents for VB-H43




































































































































































































Search results

Summary of Contents for VB-H43

Reviews:

Brands by name

Popular brands

Canon VB-H43, Operation Manual

Search results

Summary of Contents for VB-H43

Reviews:

Brands by name

Popular brands