Canon Remote FAX Kit-A1 Service Manual Download Page 40

Page: 40 / 42

4-12

Maintenance > Related Error Code > (Receiving) from the Fax Server

(Sending) to the Fax Server

Errors occurring when sending from a remote fax machine to the fax server.

Display

Code

HD full (temporary)

702

HD full (image and document control)

703

Destination unknown

704

Address book locked by another user

706

Server connection error

771

Server-side factor error

801

Network connection error

753

Server unknown

802

TCP/IP error

755

Department ID authentication error

701

Access Management System error

856

User name/password error

806

User name/password error

762

T-4-4

(Receiving) from the Fax Server

Errors occurring when receiving from the fax server to a remote fax machine.

Examples of error recorded in Remote FAX and FAX server at transmission from Remote

FAX are indicated below.

Display

Code

There is no recording paper

"SUPPLY REC. PAPER"

There is no paper on the destination side

"NO RX PAPER"

Check the document

"CHECK DOCUMENT"

The document is too long

"DOCUMENT TOO LONG"

Waiting to redial

"REDIALING"

Unregistered

"NO TEL #"

The line was busy

"LINE BUSY"

The server disc is full

Try again from the beginning

"START AGAIN"

There is no answer on the destination side

"NO ANSWER"

F code cannot be sent

"NO SUB TX"

The password cannot be sent

"NO PWD TX"

T-4-5

Summary of Contents for Remote FAX Kit-A1











































Search results

Summary of Contents for Remote FAX Kit-A1

Reviews:

Related manuals for Remote FAX Kit-A1

Brands by name

Popular brands

Canon Remote FAX Kit-A1, Service Manual

Search results

Summary of Contents for Remote FAX Kit-A1

Reviews:

Related manuals for Remote FAX Kit-A1

Brands by name

Popular brands