Canon PowerShot G3 Page 88 Error Code List Download

Page: 88 / 310

Chapter 2: Service Error Codes

2-28

Cause

Remedy

##210

[

] CD (control document) communication is

not possible

• The other party cannot use the CD com-

munications function (i.e., Canon mode
relay and confidential for G4); try a differ-
ent method of communication.

• The other party cannot use CD communi-

cation in Canon mode.

• The other party does not support CD com-

bination in Canon mode.

Cause

Remedy

##220

[ TX/RX ] System error (e.g., main program may

have gone away)

• Turn off and then on the power.
• Correct it by referring to the Service

Manual.

• Noise caused the CPU to malfunction.
• A fault occurred in the software.
• A fault occurred in the hardware.
• A hard disk error occurred.

Summary of Contents for PowerShot G3






















































































































































































































































































































Search results

Summary of Contents for PowerShot G3

Reviews:

Related manuals for PowerShot G3

Brands by name

Popular brands

Canon PowerShot G3, Error Code List

Search results

Summary of Contents for PowerShot G3

Reviews:

Related manuals for PowerShot G3

Brands by name

Popular brands