Canon PowerShot G3 Error Code List Download Page 84

Page: 84 / 310

Chapter 2: Service Error Codes

2-24

Cause

Remedy

##200

[ RX ] During image reception, a carrier is not

detected for 5 sec

• Ask the operator of the other party to in-

crease the transmission level

so that the

image signal may be received correctly.

• Ask the operator of the other party to de-

crease the transmission start speed.

• Provide echo remedy 3

• Decrease the transmission level

so that

an echo of transmitted CFR will not be re-
ceived.

• The line condition is poor, and the image

signal cannot be received.

• The training signal cannot be received be-

cause of an echo of CFR, causing a time-
over condition.

Cause

Remedy

##201

[ TX/RX ] DCN was received through a non-normal

procedure

• The other party is not ready for reception

(e.g., out of recording paper).

• The user telephone number has not been

registered (if the receiving machine is a
RICOH 3000L).

• During reception, a talk reservation was

made; however, a call was not answered.

• Ask the operator of the other party to set

the machine for reception (as by setting re-
cording paper).

• Register the user telephone number.

• Contact the other party by telephone.

Summary of Contents for PowerShot G3






















































































































































































































































































































Search results

Summary of Contents for PowerShot G3

Reviews:

Canon PowerShot G3, Error Code List, Page: 84 / 310

Search results

Summary of Contents for PowerShot G3

Reviews: