Canon PowerShot G3 Error Code List Download Page 66

Page: 66 / 310

Chapter 2: Service Error Codes

2-6

Cause

Remedy

##011

[ RX ] In G2 reception, the image signal cannot be

received for 5 sec after transmission of
CFR2

• Ask the operator of the other party to in-

crease the transmission level

so that the

image signal may be received correctly.

• Adjust the NL equalizer

so that the im-

age signal may be received correctly.

• The line condition is poor, and the image

signal cannot be received correctly.

Cause

Remedy

##012

[ RX ] In G2 reception, a signal other than PIS or

GC2 is received after transmission of MCF2
or GI2

• Record the protocol on a DAT or MD, and

have it analyzed by the local Canon office
and/or Technical Center.

• The procedure signal has a fault.

Summary of Contents for PowerShot G3






















































































































































































































































































































Search results

Summary of Contents for PowerShot G3

Reviews:

Canon PowerShot G3, Error Code List, Page: 66 / 310

Search results

Summary of Contents for PowerShot G3

Reviews: