manualshive.com logo in svg

Canon PowerShot G3, Error Code List, Page: 51 / 310

Share
Download
Canon PowerShot G3 Error Code List Download Page 51

Chapter1: User Error Codes

1-38

Cause

Remedy

#110

[ TX/RX ] In a fax machine supporting the Internet

through a provider, a customer ID error
(invalid user ID detection) occurred during
negotiation with the server

• Register the correct user ID.

• Sign an agreement with the provider.

• The user ID registered as part of the user

data does not match the terms of the con-
tract.

• No agreement has been signed with the pro-

vider.

Cause

Remedy

#111

[ TX/RX ] In a fax machine supporting the Internet

through a provider, a PIN code error (invalid
password detection) occurred during
negotiation with the server

• Register the correct password.

• The password registered as part of the user

data does not match the terms of the agree-
ment.

Summary of Contents for PowerShot G3























































































































































































































































































































Reviews:

No comments