Canon PowerShot G3 Page 234 Error Code List Download

Page: 234 / 310

Chapter 2: Service Error Codes

2-174

Cause

Remedy

##1132 [ TX/RX ] The timer went ON waiting for a response

from the CCU

• Turn off and then on the power.
• Replace the PCB that includes the CCU.

• A command was issued to the CCU, but

no response came.

Cause

Remedy

##1145 [ TX/RX ] The call settings have not been made

• Start a communication once again.
• Print out a communications analysis list,

and analyze it.

• The call setting failed without receiving a

cause number.

Summary of Contents for PowerShot G3






















































































































































































































































































































Search results

Summary of Contents for PowerShot G3

Reviews:

Related manuals for PowerShot G3

Brands by name

Popular brands

Canon PowerShot G3, Error Code List

Search results

Summary of Contents for PowerShot G3

Reviews:

Related manuals for PowerShot G3

Brands by name

Popular brands