Canon PowerShot G3 Error Code List Download Page 233

Page: 233 / 310

Chapter 2: Service Error Codes

2-173

Cause

Remedy

##1130 [ TX/RX ] Channel D is faulty

• Check to find out if the wiring between the

socket of the ISDN line and the terminal is
correct.

• Check to find out if the cable is too long,

or the cable is crushed.

• Check to find out if T and R of the cable

are reversed.

• Check to find out if the terminal resistance

is connected only to a single point.

• Start a communication once again.
• Print out a communications analysis list,

and analyze it.

• Contact the telephone company or the ex-

change manufacturer.

• A fault occurred in channel D, layer 2 (data

link layer) or lower. The line cable has poor
contact, or the wiring signal is faulty.

Cause

Remedy

##1131 [ TX/RX ] The timer used to monitor the connection

of channel D went ON

• The other party may be absent or in manual

reception mode. Contact the operator.

• Print out a communications analysis list,

and analyze it.

• Contact the telephone company or the ex-

change manufacturer.

• At time of a call, a specific period of time

has passed without a response (connection,
disconnection) from the other party.

Summary of Contents for PowerShot G3






















































































































































































































































































































Search results

Summary of Contents for PowerShot G3

Reviews:

Canon PowerShot G3, Error Code List, Page: 233 / 310

Search results

Summary of Contents for PowerShot G3

Reviews: