Canon PowerShot G3 Error Code List Download Page 23 | Manualshive

Page: 23 / 310

Canon PowerShot G3 Error Code List Download Page 23

Chapter1: User Error Codes

1-10

Cause

Remedy

#018

[

TX

] Auto dialing transmission error

• The tone/pulse setting is wrong.

• The connection time for the line is too long.

• The line of the other party was engaged.

• The other party is not connected to the line,

or is not turned on so that the transmission
did not arrive.

• The other party is not a facsimile machine.

• The other party ran out of recording paper

so that the line was disconnected during
the pre-procedure.

• The 2nd dial tone does not arrive for trans-

mission to F-NET (Facsimile communica-
tion network services). [Japanese model]

• The machine was disconnected from the

line using an unidentified reason code.

• The other party did not respond.
• The other party is out of order.
• The other party is out of use for some reason.
• The exchange is congested.
• There is no line/channel that is available at

present.

• The requested line/channel cannot be used

on the side of the other party.

• Calls crashed.
• Communication is not possible at present

by reason of terminal management.

• Make the correct tone/pulse setting.

• When registering an auto-dial number, put

a relatively long pause at the end of the
telephone number to delay the start of the
T0 timer.

• Increase the T0 timer setting

*4

to prevent a

time-over condition.

• Start a call once again.

• Ask the operator of the other party to find

out the cause.

• Check the number of the other party, and

start a call once again.

• Ask the operator of the other machine to

set recording paper.

• Check to make sure that a subscription has

been signed for F-NET, and inform the tele-
phone company that the line is out of order.

• Wait for a while, and start a call once again.
• Check to make sure that the other party is

tuned on.

• Ask the operator of the other party to find

out the cause.

«
...
21
22
23
24
25
...
»

Summary of Contents for PowerShot G3























































































































































































































































































































Reviews:

No comments