Canon PowerShot G3 Error Code List Download Page 222

Page: 222 / 310

Chapter 2: Service Error Codes

2-162

Cause

Remedy

##1088 [ TX/RX ] Incompatible destination

• Check the model and the communication

mode (G4, G3, TEL) of the other party,
and start a communication once again.

• Print out a communications analysis list,

and analyze it.

• Contact the telephone company or the ex-

change manufacturer to find out the nature
of cause number #88.

• Ask the operator of the other party to dis-

connect other terminals from the line, and
start a communication once again.

• Print out a communications analysis list,

and analyze it.

• Contact the telephone company or the ex-

change manufacturer to find out the nature
of cause number #88.

• Cause number #88 (Incompatible destina-

tion) arrived from the network. The other
party is set to a call mode different from
the machine.

• A different terminal responded, but it is

bus-connected to the other party.

Cause

Remedy

##1089 [ TX/RX ] Lane busy

[German model]

• Start a communication once again.
• Print out a communications analysis list,

and analyze it.

• Contact the telephone company or the ex-

change manufacturer to find out the nature
of cause number #89.

• Cause number #89 (Lane busy) arrived

from the network.

Summary of Contents for PowerShot G3






















































































































































































































































































































Search results

Summary of Contents for PowerShot G3

Reviews:

Canon PowerShot G3, Error Code List, Page: 222 / 310

Search results

Summary of Contents for PowerShot G3

Reviews: