manualshive.com logo in svg

Canon PowerShot G3, Error Code List, Page: 191 / 310

Share
Download
Canon PowerShot G3 Error Code List Download Page 191

Chapter 2: Service Error Codes

2-131

Cause

Remedy

##801

[ TX/RX ] The allowed number of signal

re-transmissions (3 times) to the hard disk
was exceeded

• Check the connection of the connectors as-

sociated with the hard disk.

• Replace the hard disk.

• There is no response to a signal sent to the

hard disk.

Cause

Remedy

##800

[

TX

] Multifile transmission error

• Transmit to the other party using a normal

means of transmission to find out the cause.

• Record the protocol on a DAT or MD, and

have it analyzed by the local Canon office
and/or Technical Center.

• While in relay operation in response to a

relay control request, a multifile transmis-
sion error occurred.

Summary of Contents for PowerShot G3























































































































































































































































































































Reviews:

No comments