manualshive.com logo in svg

Canon PowerShot G3, Error Code List

Get started with the Canon PowerShot G3 effortlessly by downloading the free user manual from our website. This comprehensive manual guides you through the functions and features of this exceptional camera. It's easy to download, find it now at manualshive.com.

Share
Download
background image

Chapter 2: Service Error Codes

2-123

Cause

Remedy

##783

[

TX

] In ECM transmission, the allowed number of

procedure signal re-transmissions was
exceeded or a T5 time-over (60 sec) condition
occurred after transmission of EOR-EOM

• Start G3 mode, and transmit once again

(Prohibit the ECM mode).

• Decrease the transmission start speed.
• Record the protocol on a DAT or MD, and

have it analyzed by the local Canon office
and/or Technical Center.
1. Increase the T5 timer setting to avoid

an error.

2. Change the ECM frame size from 256

bytes to 64 bytes. (This may not be pos-
sible with some models.)

• The page buffer of the other party is full or

is engaged; as such, although RNR was
received after transmission of EOR-EOM
and then RR was transmitted, no signifi-
cant signal was received correctly thereaf-
ter.

Remedy

##782

[

TX

] In ECM transmission, DCN was received

after transmission of EOR-EOM

• Increase the transmission level

*1

 so that the

other party may receive EOR-EOM cor-
rectly.

• Adjust the NL equalizer

*2

 so that the other

party may receive EOR-EOM correctly.

• Add an echo protect tone to the V.29 mo-

dem signal for transmission

*8

.

• Transmit once again.

• The line condition is poor, and the other

party cannot receive EOR-EOM correctly.

• The Stop key was pressed during a com-

munication.

Cause

Summary of Contents for PowerShot G3























































































































































































































































































































Reviews:

No comments

Related manuals for PowerShot G3

GE J1456W Brugsanvisning preview
J1456W
Brand: GE Pages: 86
Tamron B023 Owner'S Manual preview
B023
Brand: Tamron Pages: 4
Tamron A067 Owner'S Manual preview
A067
Brand: Tamron Pages: 4
Tamron A025 Owner'S Manual preview
A025
Brand: Tamron Pages: 4
Tamron A007 User Manual preview
A007
Brand: Tamron Pages: 2
Tamron 360EM User Manual preview
360EM
Brand: Tamron Pages: 6
Meiji Techno SI-C600N Operating Manual preview
SI-C600N
Brand: Meiji Techno Pages: 16
AGFA ePhoto CL20 User Manual preview
ePhoto CL20
Brand: AGFA Pages: 34
Vivitar Vivicam 3780 User Manual preview
Vivicam 3780
Brand: Vivitar Pages: 51
Tamron SP 70-210mm F/3.5 19AH Owner'S Manual preview
SP 70-210mm F/3.5 19AH
Brand: Tamron Pages: 14
Insane Audio IACAM1 User Manual preview
IACAM1
Brand: Insane Audio Pages: 2
TTI Buddy BX2 User Manual preview
Buddy BX2
Brand: TTI Pages: 31
Minolta FREEDOM ZOOM 130 Manual preview
FREEDOM ZOOM 130
Brand: Minolta Pages: 33
LEXIBOOK DJ045_01 Series User Manual preview
DJ045_01 Series
Brand: LEXIBOOK Pages: 54
VCS VCS2500 Manual preview
VCS2500
Brand: VCS Pages: 17
Intevac MicroVista NIR User Manual preview
MicroVista NIR
Brand: Intevac Pages: 30
Orion GST-624i User Manual preview
GST-624i
Brand: Orion Pages: 28
Apexis APM-J012-L-WS User Manual preview
APM-J012-L-WS
Brand: Apexis Pages: 55

Brands by name

Popular brands

Load more brands