manualshive.com logo in svg

Canon PowerShot G3, Error Code List, Page: 176 / 310

Share
Download
Canon PowerShot G3 Error Code List Download Page 176

Chapter 2: Service Error Codes

2-116

Cause

Remedy

##768

[

TX

] In ECM transmission, the allowed number of

procedure signal re-transmissions was
exceeded or a T5 time-over (60 sec) condition
occurred after transmission of PPS-EOP

• Start G3 mode, and transmit once again

(Prohibit the ECM mode).

• Decrease the transmission start speed.
• Record the protocol on a DAT or MD, and

have it analyzed by the local Canon office
and/or Technical Center.
1. Increase the T5 timer setting to avoid

an error.

2. Change the ECM frame size from 256

bytes to 64 bytes. (This may not be pos-
sible with some models.)

• The page buffer of the other party is full or

is engaged; as such, although RNR was
received after transmission of PPS-EOP
and then RR was transmitted, no signifi-
cant signal was received correctly thereaf-
ter.

Cause

Remedy

##769

[

TX

] In ECM transmission, the allowed number

of procedure signal re-transmissions was
exceeded after transmission of PPS-EOP

• Increase the transmission level

*1

 so that the

other party may receive CTC correctly.

• Ask the operator of the other party to  in-

crease the transmission level

*1

 so that the

signal may be received correctly.

• The line condition is poor; as such, al-

though PPR was received 4 times after
transmission of PPS-EOP and then CTC
was transmitted, the other party could not
receive it correctly.

• The line condition is poor; as such, al-

though PPR was received 4 times after
transmission of PPS-EOP and then CTC
was transmitted, no significant signal was
received correctly thereafter.

Summary of Contents for PowerShot G3























































































































































































































































































































Reviews:

No comments