manualshive.com logo in svg

Canon PowerShot G3, Error Code List

Get started with the Canon PowerShot G3 effortlessly by downloading the free user manual from our website. This comprehensive manual guides you through the functions and features of this exceptional camera. It's easy to download, find it now at manualshive.com.

Share
Download
background image

Chapter 2: Service Error Codes

2-108

Cause

Remedy

##753

[

TX

] In ECM transmission, the allowed number of

procedure signal re-transmissions was
exceeded or a T5 time-over (60 sec) condition
occurred after transmission of PPS-NULL

• Start G3 mode, and transmit once again

(Prohibit the ECM mode).

• Decrease the transmission start speed.
• Record the protocol on a DAT or MD, and

have it analyzed by the local Canon office
and/or Technical Center.
1. Increase the T5 timer setting to avoid

an error.

2. Change the ECM frame size from 256

bytes to 64 bytes. (This may not be pos-
sible with some models.)

• The page buffer of the other party is full or

is engaged; as such, although RNR was
received after transmission of PPS-NULL
and then RR was transmitted, no signifi-
cant signal was received correctly thereaf-
ter.

Cause

Remedy

##752

[

TX

] In ECM transmission, DCN was received

after transmission of PPS-NULL

• Increase the transmission level

*1

 so that the

other party may receive PPS-NULL cor-
rectly.

• Adjust the NL equalizer

*2

 so that the other

party may receive PPS-NULL correctly.

• Add an echo protect tone to the V.29 mo-

dem signal for transmission

*8

.

• Transmit once again.

• The line condition is poor, and the other

party cannot receive PPS-NULL correctly.

• The Stop key was pressed during a com-

munication.

Summary of Contents for PowerShot G3























































































































































































































































































































Reviews:

No comments

Related manuals for PowerShot G3

Canon EOS REBEL T6i Basic Instruction Manual preview
EOS REBEL T6i
Brand: Canon Pages: 212
Canon PowerShot A410 Specification preview
PowerShot A410
Brand: Canon Pages: 4
Canon PowerShot A510 Quick Start Manual preview
PowerShot A510
Brand: Canon Pages: 2
Canon IXUS 30 Quick Start Manual preview
IXUS 30
Brand: Canon Pages: 2
Canon EOS 70D Quick Reference Manual preview
EOS 70D
Brand: Canon Pages: 2
Canon EOS-1 Settings Manual preview
EOS-1
Brand: Canon Pages: 48
Canon EF 100-400mm f/4.5-5.6L IS USM Parts Catalog preview
EF 100-400mm f/4.5-5.6L IS USM
Brand: Canon Pages: 9
Canon EF-M 18-55mm f3.5-5.6 IS STM Instruction preview
EF-M 18-55mm f3.5-5.6 IS STM
Brand: Canon Pages: 12
Canon PowerShot A5 Quick Start Manual preview
PowerShot A5
Brand: Canon Pages: 28
Panasonic DMC-ZS30 Basic Operating Instructions Manual preview
DMC-ZS30
Brand: Panasonic Pages: 36
Panasonic DMCFP2 - DIGITAL STILL CAMERA Operating Instructions For Advanced Features preview
DMCFP2 - DIGITAL STILL CAMERA
Brand: Panasonic Pages: 94
Panasonic DMC-TZ71 Operating Instructions Manual preview
DMC-TZ71
Brand: Panasonic Pages: 305
Panasonic DMC-GF6K Guía Del Usuario preview
DMC-GF6K
Brand: Panasonic Pages: 48
Panasonic DMC-GF3XK Basic Operating Instructions Manual preview
DMC-GF3XK
Brand: Panasonic Pages: 52
Panasonic DMC-GF3C Owner'S Manual preview
DMC-GF3C
Brand: Panasonic Pages: 56
Panasonic DMC-FZ150K Basic Operating Instructions Manual preview
DMC-FZ150K
Brand: Panasonic Pages: 40
Panasonic DMC-FX90K Basic Owner'S Manual preview
DMC-FX90K
Brand: Panasonic Pages: 45
Panasonic DMC-FX48K - Lumix Digital Camera Instrucciones Básicas De Funcionamiento preview
DMC-FX48K - Lumix Digital Camera
Brand: Panasonic Pages: 28

Brands by name

Popular brands

Load more brands