Canon PowerShot G3 Page 158 Error Code List Download

Page: 158 / 310

Chapter 2: Service Error Codes

2-98

Cause

Remedy

##713

[

] In CHT transmission, a signal other than

RR, RNR, or REJ was received after
transmission of an image signal

• Record the protocol on a DAT or MD, and

have it analyzed by the local Canon office
and/or Technical Center.

• The procedure signal is faulty.

Remedy

##714

[

] During a re-transmission procedure in CHT

transmission, REJ was not received,
causing a time-over condition

• Increase the transmission level

so that that

other party may receive ACK correctly.

• Ask the operator of the other party to in-

crease the transmission level

so that REJ

may be received correctly.

• The line condition is poor, and the other

party cannot receive ACK correctly.

• The line condition is poor, and REJ cannot

be received correctly.

Summary of Contents for PowerShot G3






















































































































































































































































































































Search results

Summary of Contents for PowerShot G3

Reviews:

Related manuals for PowerShot G3

Brands by name

Popular brands

Canon PowerShot G3, Error Code List

Search results

Summary of Contents for PowerShot G3

Reviews:

Related manuals for PowerShot G3

Brands by name

Popular brands