manualshive.com logo in svg

Canon PowerShot G3, Error Code List

Get started with the Canon PowerShot G3 effortlessly by downloading the free user manual from our website. This comprehensive manual guides you through the functions and features of this exceptional camera. It's easy to download, find it now at manualshive.com.

Share
Download
background image

Chapter 2: Service Error Codes

2-77

Cause

Remedy

##351

[ TX/RX ] Contact sensor LED activation period error

• Check to see that the control panel is closed

firmly.

• Check the connection between the contact

sensor and the system control board.

• Clean the reading glass of the contact sen-

sor.

• Turn off and then on the power; after the

end of auto light intensity adjustment,
check to see that the machine is in standby
without an error. Thereafter, make a copy
to see that the copy image is normal.

• Replace the contact sensor unit.
• Replace the system control board.

• During a checksum error in shading data

at time of power-on or during calibration,
the LED was turned on to adjust the acti-
vation period; however, the fault was not
corrected.

Cause

Remedy

##350

[

TX

] CS right edge sensor of the contact sensor

(CS) fails

• Replace the CS right edge sensor.

• Replace the CS motor.

• Replace the CS right edge sensor.

If the CS does not move from the right edge
stop position,
• The CS right edge sensor remains ON or

OFF.

• The CS right edge sensor is out of order.

• The CS motor fails to operate.
• The CS motor operates out of sync.

If the CS does not stop at the right edge stop
position,
• The CS right edge sensor remains ON or

OFF.

• The CS right edge sensor is out of order.

Summary of Contents for PowerShot G3























































































































































































































































































































Reviews:

No comments

Related manuals for PowerShot G3

Canon F-1 Quick Start Manual preview
F-1
Brand: Canon Pages: 4
CamPro 1826 Instruction Manual & Warranty Card preview
1826
Brand: CamPro Pages: 14
Vigilate VIGIFC User Manual preview
VIGIFC
Brand: Vigilate Pages: 2
Olympus ED 14-42mm f3.5-5.66 EZ Instructions Manual preview
ED 14-42mm f3.5-5.66 EZ
Brand: Olympus Pages: 15
Tamron A022 Owner'S Manual preview
A022
Brand: Tamron Pages: 4
Zipsnip OPS-8 User Manual preview
OPS-8
Brand: Zipsnip Pages: 26
Navaio NGC-7522R User Manual preview
NGC-7522R
Brand: Navaio Pages: 58
ELRO CC4000 Quick Start Manual preview
CC4000
Brand: ELRO Pages: 2
Blaupunkt VIO-H30 Quick Start Manual preview
VIO-H30
Brand: Blaupunkt Pages: 61
ZEISS IKON Contaflex Super B Instruction Manual preview
Contaflex Super B
Brand: ZEISS IKON Pages: 12
TeleNav Waylens Horizon User Manual preview
Waylens Horizon
Brand: TeleNav Pages: 23
Minolta Autopak-8 K7 Owner'S Manual preview
Autopak-8 K7
Brand: Minolta Pages: 40
Olympus FE 360 - Digital Camera - Compact Manual De Instruções preview
FE 360 - Digital Camera - Compact
Brand: Olympus Pages: 62
Advantech ARK-DS762 User Manual preview
ARK-DS762
Brand: Advantech Pages: 40
Nikon 2193 Manual preview
2193
Brand: Nikon Pages: 152
Argus Quick Clix QCM-099 Specification Sheet preview
Quick Clix QCM-099
Brand: Argus Pages: 1
Argus QuickClix QC-3185 Quick Start Manual preview
QuickClix QC-3185
Brand: Argus Pages: 4
Navico IP CAM-1 Installation Manual preview
IP CAM-1
Brand: Navico Pages: 2

Brands by name

Popular brands

Load more brands