Canon PowerShot G3 Error Code List Download Page 132

Page: 132 / 310

Chapter 2: Service Error Codes

2-72

Cause

Remedy

##342

[ TX/RX ] Ink absorber for cleaning has become full

• Turn off and then on the power.
• If the waste ink in the ink absorber is ap-

parently not much, do not replace, but reg-
ister an approximate value once again as
the ink absorber capacity for cleaning in
service mode.

• If the waste ink is much, replace the ink

absorber, and set '0' as ink absorber capac-
ity for cleaning in service mode.

• Replace the printer control board; then,

check the ink absorber capacity, and regis-
ter an approximate value once again as the
ink absorber capacity for cleaning in ser-
vice mode.

• Replace the system control board; then,

check the ink absorber capacity, and regis-
ter an approximate value once again as the
ink absorber capacity for cleaning in ser-
vice mode.

• The ink absorber for cleaning has become

full with waste ink.

Summary of Contents for PowerShot G3






















































































































































































































































































































Search results

Summary of Contents for PowerShot G3

Reviews:

Canon PowerShot G3, Error Code List, Page: 132 / 310

Search results

Summary of Contents for PowerShot G3

Reviews: