Canon PowerShot G3 Page 125 Error Code List Download

Page: 125 / 310

Chapter 2: Service Error Codes

2-65

Cause

Remedy

##331

[ TX/RX ] Remaining amount of ink in the BJ

cartridge cannot be detected

• See the Service Manual of the model in

question to replace the ink sensor; thereaf-
ter, register the ink detection level once
again.

• The ink sensor is faulty.

Cause

Remedy

##332

[ TX/RX ] DRAM check error has occurred for BJ

printer control

• Turn off and then on the power.
• Replace the PCB that includes the DRAM

used to control the printer.

• Turn off and then on the power.
• Replace the system control board.

• The DRAM for printer control is faulty.

• The system control board is faulty.

Summary of Contents for PowerShot G3






















































































































































































































































































































Search results

Summary of Contents for PowerShot G3

Reviews:

Related manuals for PowerShot G3

Brands by name

Popular brands

Canon PowerShot G3, Error Code List

Search results

Summary of Contents for PowerShot G3

Reviews:

Related manuals for PowerShot G3

Brands by name

Popular brands