Start Here
Easy Setup Instructions
Cassette Loading
You can load paper in both the Auto Sheet
Feeder and Cassette.
Note
At purchase, the printer is set to feed from the
Auto Sheet Feeder.
a
Pull out the cassette from the
bottom of the printer.
Cassette
Cover
b
Remove the cover of the cassette.
c
For A5 or larger sized paper, pull
the tab towards you to unlock and
extend the cassette.
Tab
A5 or larger
(nonstandard-size paper: 203 mm / 8 inches
or more in length)
5" x 7" or smaller
(nonstandard-size paper: less than 203 mm /
8 inches in length)
d
Load the paper into the cassette
with the print side facing
DOWN
.
Note
Loading paper in the cassette provides
additional paper handling flexibility. For
additional information refer to the
User’s Guide
.
QT5-0427-V02
a
Place the printer on a flat and
horizontal surface, and do not place
any objects in front of the printer. Press
the Open Button to open the Paper
Output Tray, and extend the Paper
Output Tray Extension. Open the Paper
Support and extend the Paper Support
Extension.
Caution
Before turning on the printer, remove all of the
shipping tapes.
b
Plug the power cord in the back of the
printer and connect the other end to the
wall outlet.
c
Press the
POWER
button to turn on the
printer.
1
Prepare the Printer
d
Open the Top Cover. The Print Head
Holder moves to the center.
Top Cover
e
Open the Inner Cover. Write down the
serial number located inside the printer.
You will need this to register your
product.
Inner Cover
Serial Number Location
3
Install the Ink Tanks
4
Connect the Printer and Load Paper
2
Install the Print Head
a
Remove the Print Head from its
package.
Caution
There may be some transparent or light blue ink
on the inside of the bag the print head comes in,
or the inside of the protective cap - this has no
effect on print quality. Be careful not to get ink on
yourself when handling these items.
b
Remove the orange protective cap from
the Print Head and discard it.
Protective Cap
Electrical Contacts
Print Head Nozzles
Note
Do not touch the print head nozzles and the electrical
contacts.
c
Firmly raise the Print Head Lock Lever
until it stops.
d
Insert the Print Head.
Do not touch!
e
Lower the Print Head Lock Lever
carefully.
Important
If the Top Cover is left open for more than 10
minutes, the Print Head Holder moves to the right.
Close and reopen the Top Cover to return the
Holder to the center.
a
Peel back the orange tab completely
and remove the plastic wrapper from
the ink tank.
If the orange-colored protective film is not removed
completely, problems with printing may occur.
b
Twist off and discard the orange
protective cap located on the bottom of
the ink tank.
Electrical Contacts
Ink Port
Protective Cap
Do not press!
Important
• Do not touch the electrical contacts.
• Do not touch the ink port.
c
Insert the ink tank into the right-hand
slot and press the mark on the ink
tank until it clicks into place.
d
Make sure the ink lamp lights red.
Refer to the color guide on the
Print Head Lock Lever.
e
Close the Inner Cover and the Top
Cover.
Note
If the
ALARM
lamp on the printer flashes orange after
you have closed the Top Cover, refer to “ALARM Lamp
Flashes Orange” in “Troubleshooting” of the
User’s
Guide
.
Important
Once you have installed the ink tanks, the POWER
lamp will flash green. Wait for about 2 minutes,
until the POWER lamp stops flashing and changes
to steady, non-flashing green and the printer has
stopped making operating noises, before proceed-
ing.
a
TURN THE PRINTER OFF.
Important
Be sure the printer is off before continuing, or the
computer will attempt to install the printer driver
before the printer is ready.
b
Connect one end of the USB cable to
the computer, the other to the printer.
USB Port
USB Cable
USB Cable
USB Port
c
Pinch the Paper Guide and slide it to
the left end. Load a sheet of letter- or
A4-size blank paper in the Auto Sheet
Feeder, align the paper with the right
side of the Cover Guide, then slide the
Paper Guide against the paper stack.
Cover
Guide
Print Side
Paper Guide
Hardware setup is complete.
Photo Printer
Unpack the Printer
• Please confirm the included items against the illustration printed on the lid of the packing box.
• A USB cable is necessary to connect the printer with your computer.
Series
