Canon Paper Deck Unit-F1 Service Manual Download Page 109

Page: 109 / 112

3. Fasten the screws.

• 2 Screws

4. Move the front cover fitting to the amount of the latch

plate movement. Refer to the next item "Front Cover
Positioning Adjustment" for detail.

5. Close the compartment and connect to the host

machine.

6. Feed paper from the Paper Deck. Check that L is

2.5+/-1.5mm. Re-adjust L when it is out of the range.

Front Cover Positioning

Adjustment

1. Check the gap on the front cover.

• Gap between the front cover and the right cover:

3+/-1mm

• Gap between the front cover and the upper cover:

4+/-1mm

3+/-1mm

NOTE:

Loosen the screws on the front cover and then adjust the
gap within the range.

• 6 Screws

6. Installation

103

Summary of Contents for Paper Deck Unit-F1
















































































































Search results

Summary of Contents for Paper Deck Unit-F1

Reviews:

Related manuals for Paper Deck Unit-F1

Brands by name

Popular brands

Canon Paper Deck Unit-F1, Service Manual

Search results

Summary of Contents for Paper Deck Unit-F1

Reviews:

Related manuals for Paper Deck Unit-F1

Brands by name

Popular brands