Canon OCT-A1 Operation Manual Download Page 198

Page: 198 / 276

198

8 Settings

System Settings

This section uses screens from RX Capture for OCT as examples in explanations.

[System Settings] Tab

On the [System Settings] screen, set the modality information for the OCT.

• [AE Title]

The default values for each software are as shown below. Be sure to input the values.

•

RX Capture for OCT-HS100 : Canon OCT-HS100

•

RX Capture for OCT-A1 : Canon OCT-A1

•

RX Viewer : Canon RX Viewer

•

RX Server : Canon RX Server

• [Station Name]

Input the station name.

• [Location]

Input the location.

• [Institutional Department Name]

Input the institutional department name. Be sure to input the value.

• [Institution Name]

Input the institution name. Be sure to input the value.

• [Database]

Select [Local] or [Remote] in RX Capture for OCT.
The database for RX Viewer is [Remote] and for RX Server it is [Local].

• [Server Name]

Specify the server as the database to store examination data.
Enter the server name or the IP address (IPv4). Be sure to input the value.
When you select [Local] on [Database], [Server Name] becomes [localhost].

BT8-1794-E01_RX OCT-A1_HS100 V4.6_CVS.indb 198

10/26/2020 10:50:04 AM

Summary of Contents for OCT-A1





















































































































































































































































































Search results

Summary of Contents for OCT-A1

Reviews:

Brands by name

Popular brands

Canon OCT-A1, Operation Manual

Search results

Summary of Contents for OCT-A1

Reviews:

Brands by name

Popular brands