Canon MX920 series Online Manual Download Page 176

Page: 176 / 267

1007

Cause

Possible causes include the following.

• There is no paper in the cassette (upper).
• The paper source is incorrect.
• Paper is not loaded properly.

Action

Take the corresponding actions below.

• Load paper in the cassette (upper).
• Load paper in the paper source suitable for the paper size.

The small size photo paper such as 4" x 6" (10 x 15 cm) or 5" x 7" (13 x 18 cm), or Hagaki can be
loaded in the cassette (upper).

Important

If you cut plain paper into small size such as 4" x 6" (10 x 15 cm) or 5" x 7" (13 x 18 cm) and try

to print on it, the paper jam will occur.

• Align the paper guides with the both edges of the paper when you load paper.

After carrying out the above measures, press the

button to dismiss the error.

Summary of Contents for MX920 series












































































































































































































































































Search results

Summary of Contents for MX920 series

Reviews:

Brands by name

Popular brands

Canon MX920 series, Online Manual

Search results

Summary of Contents for MX920 series

Reviews:

Brands by name

Popular brands