manualshive.com logo in svg

Canon MX720 Series, Online Manual, Page: 198 / 248

Share
Download
Canon MX720 Series Online Manual Download Page 198

Search Screen

Note

This screen is not available depending on the printer you are using.

The access points detected are listed.

1.

Detected Access Points:

The signal strength from the access point, encryption type, name of access point, and the radio
channel can be confirmed.

Important

If you connect to a network that is not protected with security measures, there is a risk of

disclosing data such as your personal information to a third party.

Note

Signal strength is displayed as follows.

: Good
: Fair
: Poor

Type of encryption is displayed as follows.

Blank: No encryption

WEP

: WEP is set

WPA

: WPA is set

WPA2

: WPA2 is set

2.

Update

Click to update the list of access points when your target access point is not detected.
If the target access point is set to the stealth mode, click 

Cancel

 to return to the previous screen

and enter the access point's Service Set Identifier in 

SSID:

 on the 

Wireless LAN

 sheet.

Wireless LAN Sheet

Note

When detecting your target access point, make sure that the access point is turned on.

3.

Set

Click to set the access point's SSID in 

SSID:

 on the 

Wireless LAN

 sheet.

Note

The 

WEP Details

 screen, the 

WPA Details

 screen, or the 

WPA2 Details

 screen appears if

the selected access point is encrypted. In this case, configure the details to use the same
encryption settings set to the access point.

Summary of Contents for MX720 Series

























































































































































































































































Reviews:

No comments