Canon MX720 Series Online Manual Download Page 173

Page: 173 / 248

Printing Out Network Setting Information

You can print out the network settings of the machine such as its IP address and SSID.

Important

This print out contains valuable information about your computer. Handle it with care.

Make sure that the machine is turned on.

Confirming that the Power Is On

Load a sheet of A4 or Letter-sized plain paper.

Loading Paper

Press the

MENU

button.

The menu screen is displayed.

Select

Setup

, then use the

button to confirm the selection.

Select

Device settings

, then use the

button to confirm the

selection.

Use the

button to select

LAN settings

, then use the

button to confirm

the selection.

Use the

button to select

Confirm LAN settings

, then use the

button to

confirm the selection.

Use the

button to select

Print LAN details

, then use the

button to

confirm the selection.

Use the

button to select

Yes

, then use the

button to start printing.

The machine starts printing the network setting information.
The following information on the machine's network setting is printed out.

Item

Explanations of the item

Setting

Wireless LAN

Enable/Disable

Connection

Status of the Wireless LAN Active/Inactive

MAC Address

XX:XX:XX:XX:XX:XX

SSID

SSID of the wireless LAN

Communication Mode

Infrastructure

Channel

XX (1 to 13)

Encryption

Method of the Encryption

none/WEP/TKIP/AES

WEP Key Length

Inactive/128/64

Authentication

Method of the
Authentication

none/auto/open/shared/WPA-PSK/
WPA2-PSK

Signal Strength

0 to 100 [%]

TCP/IP Version

IPv4 & IPv6/IPv4

Summary of Contents for MX720 Series

























































































































































































































































Search results

Summary of Contents for MX720 Series

Reviews:

Canon MX720 Series, Online Manual, Page: 173 / 248

Search results

Summary of Contents for MX720 Series

Reviews: