Canon MP630 SERIES Service Manual Download Page 30 | Manualshive

Page: 30 / 47

background image

(8) Spur unit and platen unit removal

1) Remove the ink sensor and the inner cover sensor from the front chassis (1 screw each).

2) From the left and right sides of the spur unit, release the springs (2 on the left side, 1 on the right side). Then, slowly pull

the spur unit upward to remove it from the platen unit.

28 / 45

«
...
28
29
30
31
32
...
»

Summary of Contents for MP630 SERIES
















































Reviews:

No comments

Related manuals for MP630 SERIES

Brand: Canon Pages: 16

IR5000 - iR B/W Laser

Brand: Canon Pages: 86

Brand: Canon Pages: 48

Brand: Oki Pages: 24

Brand: VAF instruments Pages: 24

Brand: 3DP Pages: 12

870 - SuperScript B/W Laser Printer

Brand: NEC Pages: 8

Brand: CAB Pages: 40

Magicolor 2 plus

Brand: QMS Pages: 90

Magicolor 2 Desklaser

Brand: QMS Pages: 4

Brand: QMS Pages: 8

Brand: QMS Pages: 94

Brand: QMS Pages: 6

DocuPrint C3055 DX

Brand: Xerox Pages: 20

Brand: Oki Pages: 28

Brand: Oki Pages: 22

image RUNNER 3045

Brand: Canon Pages: 14

Brand: Oki Pages: 512

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands