Canon MP630 SERIES Service Manual Download Page 16

Page: 16 / 47

3. REPAIR

3-1. Notes on Service Part Replacement (and Disassembling / Reassembling)

MP630 / MP638

TABLE OF CONTENTS

Service part

Notes on replacement

Adjustment / settings

Operation check

Logic board ass'y

- Before removal of the logic board

ass'y, remove the power cord, and

allow for approx. 1 minute (for

discharge of capacitor's

accumulated charges), to prevent

damages to the logic board ass'y.

- Before replacement, check the ink

absorber counter value (by

service test print or EEPROM

information print).

After replacement:

1. Initialize the EEPROM.

2. Set the ink absorber counter

value.

3. Set the destination in the

EEPROM.

4. Correct the CD / DVD and

automatic print head alignment

sensors.

5. Check the ink system function.

6. Perform LF / Eject correction.

7. Perform button and LCD test.

Perform 1 to 7 in the service

mode.

[See

3-3. Adjustment / Settings,

(6) Service mode

, for details.]

8. Perform print head alignment

and LCD language setting in the

user mode.

- EEPROM information print

- Service test print

- Printing via USB connection

- Copying

- Direct printing from a digital

camera (PictBridge)

Absorber kit

After replacement:

1. Reset the ink absorber counter.

[See

3-3. Adjustment / Settings,

(6) Service mode

, for details.]

- Ink absorber counter volume

print (After the ink absorber

counter is reset, the counter

value is printed automatically.)

Carriage unit

At replacement:

1. Before removal of the carriage

rail, mark the carriage rail

position.

[See

3-2. Special Notes on

Repair Servicing, (7) Carriage

unit removal

, for details.]

2. Apply grease to the sliding

portions of the carriage rail.

[See

3-3. Adjustment / Settings,

(3) Grease application

, for

details.]

3. Check the ink system function.

[See

3-3. Adjustment / Settings,

(6) Service mode

, for details.]

4. Perform print head alignment in

the user mode.

- Service test print (Confirm

CD / DVD and automatic print

head alignment sensor

correction, and ink system

function.)

Switch system unit

- The red screws securing the paper

feed motor are allowed to be

loosened only for paper feed

motor replacement. (DO NOT

loosen them in any other cases.)

At replacement:

1. Adjust the paper feed motor.

[See

3-3. Adjustment / Settings,

(1) Paper feed motor adjustment

for details.]

- EEPROM information print

- Service test print

Paper feed motor

Platen unit

After replacement:

1. Perform LF / Eject correction in

the service mode.

[See

3-3. Adjustment / Settings,

(6) Service mode

, for details.]

- EEPROM information print

- Service test print

Spur unit

- DO NOT contact the spur edges.

After replacement:

1. Check the ink system function.

2. Perform LF / Eject correction in

the service mode.

[See

3-3. Adjustment / Settings,

- EEPROM information print

- Service test print

14 / 45

Summary of Contents for MP630 SERIES
















































Search results

Summary of Contents for MP630 SERIES

Reviews:

Related manuals for MP630 SERIES

Brands by name

Popular brands

Canon MP630 SERIES, Service Manual

Search results

Summary of Contents for MP630 SERIES

Reviews:

Related manuals for MP630 SERIES

Brands by name

Popular brands