manualshive.com logo in svg

Canon MF724Cdw, Service Manual

Share
Download
Canon MF724Cdw Service Manual Download Page 221

2. Free the harness [1] and [2] from the Harness Guide

[A] and [B].

[1]

[2]

[B]

[2]

[1]

[A]

2x

3. Remove the Harness Guide [1].

• Harness Guide [A]
• 2 Boss [2]
• 2 Hooks [3]

[A]

[1]

[2]

[3]

[2]

1x

4. Remove the Pickup Motor [1].

• 2 Screws [2]
• 1 Connector [3]

[1]

[3]

[2]

2x

1x

 Removing the Pickup Unit

■ Preparation

1. Removing the Right Cover.(Refer to 

“Removing the

Right Cover” on page 120

 )

2. Removing the Left Cover.(Refer to 

“Removing the

Left Cover” on page 118

 )

3. Removing the Right Front Cover.(Refer to

“Removing the Right Front Cover” on page 121

 )

4. Removing the ADF Unit + Reader Unit.(Refer to

“Removing the ADF Unit + Reader Unit” on page
130

)

5. Removing the Rear Upper Cover.(Refer to

“Removing the Rear Upper Cover” on page 123

)

6. Removing the Upper Cover.(Refer to 

“Removing the

Upper Cover” on page 125

)

7. Removing the Wireless LAN PCB.(MF728Cdw /

727Cdw / 724Cdw only)(Refer to 

“Removing the

Wireless LAN PCB (MF728Cdw / 727Cdw / 724Cdw)”
on page 157

)

8. Removing the Main Controller PCB.(Refer to

“Removing the Main Controller PCB” on page 157

)

9. Removing the Main Controller Support Plate.(Refer

to 

“Removing the Main Controller Support Plate” on

page 161

)

10. Removing the Fixing/Fixing Power Supply Cooling

Fan Unit.(Refer to 

“Removing the Fixing/Fixing

Power Supply Cooling Fan Unit” on page 180

)

4. Disassembly/Assembly

213

Summary of Contents for MF724Cdw








































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands