manualshive.com logo in svg

Canon MF724Cdw, Service Manual

Share
Download
Canon MF724Cdw Service Manual Download Page 179

CAUTION:

When connecting the Flat Cable, be sure to perform
the following; while pushing the Flat Cable [1] against
the connector with a lock [2], check that the line on the
edge [A] of the Flat Cable Connector and the line on
the edge [B] of the Flat Cable Connector Lock are
parallel, and then close the Flat Cable Connector Lock
[3].

[1]

[3]

[2]

[A]

[B]

 Removing the NFC PCB

(MF727Cdw / 726Cdw)

■ Preparation

1. Remove the the Control Panel Unit.(Refer to

“Removing the Control Panel Unit” on page 169

)

■ Procedure

CAUTION:

Do not touch the IC part [A] of the LCD Flat Cable [1].

[A]

1. Remove the NFC PCB [1].

• 1 Connector [2]
• 1 Screws [3]

[1]

1x

1x

[3]

[2]

 Removing the FAX PCB

(MF728Cdw / 727Cdw / 725Cdw)

■ Preparation

1. Removing the Right Cover.(Refer to 

“Removing the

Right Cover” on page 120

)

2. Removing the Controller Cover.(Refer to 

“Removing

the Controller Cover” on page 157

)

3. Removing the Wireless LAN PCB.(MF728Cdw /

727Cdw / 724Cdw only) (Refer to 

“Removing the

Wireless LAN PCB (MF728Cdw / 727Cdw / 724Cdw)”
on page 157

)

4. Removing the Main Controller PCB.(Refer to

“Removing the Main Controller PCB” on page 157

)

5. Removing the Main Controller Support Plate.(Refer

to 

“Removing the Main Controller Support Plate” on

page 161

)

■ Procedure

1. Remove the Fax PCB [1].

• 1 Flat Cable [2]
• 1 Connector [3]
• 4 Screws [4]

[4]

[4]

[4]

[1]

[3]

[2]

4x

2x

4. Disassembly/Assembly

171

Summary of Contents for MF724Cdw








































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands