Canon MF724Cdw Service Manual Download Page 173

Page: 173 / 327

Removing the Low Voltage

Unit

■ Preparation

1. Removing the Right Cover.(Refer to

“Removing the

Right Cover” on page 120

)

2. Removing the Right Front Cover.(Refer to

“Removing the Right Front Cover” on page 121

)

3. Removing the Controller Cover.(Refer to

“Removing

the Controller Cover” on page 157

)

4. Removing the Wireless LAN PCB.(MF728Cdw /

727Cdw / 724Cdw only) (Refer to

“Removing the

Wireless LAN PCB (MF728Cdw / 727Cdw / 724Cdw)”
on page 157

)

5. Removing the Main Controller PCB.(Refer to

“Removing the Main Controller PCB” on page 157

)

6. Removing the Main Controller Support Plate.(Refer

“Removing the Main Controller Support Plate” on

page 161

)

7. Removing the Fixing/Fixing Power Supply Cooling

Fan Unit.(Refer to

“Removing the Fixing/Fixing

Power Supply Cooling Fan Unit” on page 180

)

■ Procedure

1. Free the harness [1] from the guide [A].

• 1 Connector [2]

2. Free the harness [3] from the guide [B].

• 1 Connector [4]

[A]

[1]

[2]

[B]

[3]

[4]

3. Slide and open the Power Supply Unit [1] in the

direction of the arrow.

• 6 Screws [2]
• 1 Screw [3] (Toothed washer screw)
• 2 Claws [4]

[1]

[2]

[3]

[4]

4. Remove 3 connectors [1].

[1]

4. Disassembly/Assembly

165

Summary of Contents for MF724Cdw








































































































































































































































































































































Search results

Summary of Contents for MF724Cdw

Reviews:

Brands by name

Popular brands

Canon MF724Cdw, Service Manual

Search results

Summary of Contents for MF724Cdw

Reviews:

Brands by name

Popular brands