Home
/
Canon
/
IR5000 - iR B/W Laser
/
Service Manual

Canon IR5000 - iR B/W Laser, Service Manual

Share

Page: 67 / 839

Canon IR5000 - iR B/W Laser Service Manual Download Page 67

COPYRIGHT © 2000 CANON INC.

2000 2000 2000 2000

CANON iR5000/iR6000 REV.0 JULY 2000

CHAPTER 3 INSTALLATION

3-3 S

2. Unpacking and Installation

2.1 Before Starting the Work

Be sure to observe the following when installing the machine:

1. If the machine is moved from a cold to warm place for installation, con-

densation can occur in its pickup/feed assembly. Leave the machine
alone without unpacking for an hour or more before starting the work.
(The term condensation refers to the formation of droplets of water on a
metal surface caused by rapidly cooling moisture in the air.)

2. If flights of stairs are used to move the machine into or out of the site of

installation, be sure to observe the following:
2.1 Take out the ADF assembly, fixing/feeding assembly, and duplexing

unit, and move them separately from the body.

2.2 When lifting the machine, do not use its four grips (left, right); in-

stead, hold it by its four bottom corners.

2.3 The machine weighs 210 kg. Be sure to work in a group of four.

3. Shift up the two adjusters found on the machine’s bottom (front) to

make sure that they are released. The adjusters can slip off while the
machine is being moved. Be sure to pay attention not to lose them.

4. Be sure to work in a group of three or more when installing the ma-

chine. When removing the pad and bottom plate, arrange one person at
the rear and one person at the front to hold the grips while one person
engages in removal.

Download Free Service Manual at http://printer1.blogspot.com

«
...
65
66
67
68
69
...
»

Summary of Contents for IR5000 - iR B/W Laser








































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands