manualshive.com logo in svg

Canon iR2318 series, Service Manual, Page: 74 / 308

Share
Download
Canon iR2318 series Service Manual Download Page 74

Chapter 2  

2-20

2.4 Installing the Heater PCB

2.4.1 Preparing the parts

0020-4263

1) Prepare the following parts.

F-2-44

2.4.2 Preparing the Host Machine

0020-4264

F-2-45

1) Open the front cover [1].

F-2-46

2) Remove the rear cover [1].

- RS tightening screws (M3 x 8)[2], 4 pcs.

[1]

Heater PCB unit

1 pc.

[2]

Heater switch harness

1 pc.

[3]

Cassette heater harness

1 pc.

[4]

Heater control harness

1 pc.

[5]

Clamp

4 pcs.

[6]

Edge saddle (small)

2 pcs.

[7]

Edge saddle (large)

1 pc.

[8]

TP screw (M3x8)

2 pcs.

[8]

[7]

[6]

[5]

[1]

[2]

[3]

[4]

Before installing, make sure the host machine is turned off. If it is turned on, 
go through the following: 
1. Turn off the main power switch.
2. Disconnect the power cable (from the power outlet).
3. Disconnect the power cable.

[1]

[3]

[2]

[1]

[1]

[2]

Summary of Contents for iR2318 series





















































































































































































































































































































Reviews:

No comments