manualshive.com logo in svg

Canon iR2318 series, Service Manual, Page: 291 / 308

Share
Download
Canon iR2318 series Service Manual Download Page 291

Chapter 15

15-1

15.1 Outline

15.1.1 Overview of Upgrade

0020-4299

This machine can be upgraded by downloading system software programs from the personal computer (hereafter called as the PC) in which a user support tool

(hereafter called UST) has been loaded. The optiion can be upgraded by downloading system software programs from the personal computer (hereafter called as

the PC) in which a service support tool (hereafter called SST) has been loaded.

System software programs and upgrade tools are listed in the following table:

15.2 Downloading System Software

15.2.1 Downloading System

15.2.1.1 Downloading Procedure

0020-4303

1) Turn on the power switch of the PC and start UST.

2) When the power switch is turned on, the Found New hardware Wizard appears. Click "Cancel".

F-15-1

3) Press the Additional Functions key on the control panel of this machine to enter into the user mode. 

4) Press the down-arrow key to select "System Settings", and then press the OK key. 

5) Press the down-arrow key to select "Update Firmware", and then press the OK key. 

6) When "OK to update" appears, select “Yes” and then press the OK key.

7) When "PLEASE WAIT WAITING" appears, start the UST. 

Type

System software type Upgrade 

tool 

Remarks

Main unit

System (main controller)

UST

The main controller also controls the reader.

Boot (boot program)

UST

Boot program is upgraded automatically at the same time with System version up.

Option

Fin_U2 (Finisher-U2)

SST+Downloader PCB

Dedicated service tool (Downloader PCB: FY9-2034)
Refer to finisher service manual about the method of version up.

Summary of Contents for iR2318 series





















































































































































































































































































































Reviews:

No comments