manualshive.com logo in svg

Canon iR2318 series, Service Manual, Page: 265 / 308

Share
Download
Canon iR2318 series Service Manual Download Page 265

Chapter 13

13-5

13.3.3 Jam Codes (Related to ADF)

0020-4326

13.3.4 Jam Codes (Related to Duplex Unit)

0020-4327

13.3.5 Jam Codes (Related to Inner 2-way Tray)

0020-4328

Code

Name

Sensor No.

Description

0000

Unknown jam

-

Other errors

0007

Initial stationary

PI6,PI7,PI8 Paper is detected in the transport path before the DADF starts initial 

operation.  

0008

Read sensor delay

PI7,PI8

The read sensor does not detect paper when the paper has been fed 
by the predetermined distance since reception of a pickup request. 

0009

Read sensor stationary

PI7

The trailing edge of paper is not detected when the paper has been 
fed by the predetermined distance since detection of it by the read 
sensor.  

000a

Paper absence (Pull out 
the document.)

PI11

The Document set sensor  has been held off since start of pickup. 

000c

Delivery reversal sensor 
delay

PI6,PI7

The delivery reversal sensor does not detect paper since the paper 
has been fed by the predetermined distance since the read sensor 
was turned on.

000d

Delivery reversal sensor 
stationary

PI6

The trailing edge of paper is not detected when the paper has been 
fed by the predetermined distance since the delivery reversal sensor 
detected the paper.

000e

ADF cover open

PI10

The feeder cover was opened during operation (of the drive system).

000f

User ADF open

sensor of 
the reader 
unit

The ADF was opened during operation (of the drive system).

0010

Pickup NG

-

The registration sensor has been held off since paper pickup started.

Code

Name

Sensor No.

Description

0120

Delay jam at duplex 
paper sensor 1

SR1002

The duplex paper sensor 1 does not turn on within the specified 
time after the delivery sensor on the main unit side turns on.

0124

Delay jam at duplex 
paper sensor 2

SR1003

The duplex paper sensor 2 does not turn on within the specified 
time after the duplex reverse motor starts.

0221

Stationary jam at 
duplex paper sensor 1

SR1002

- The duplex paper sensor 1 does not turn off when the specified 
time has lapsed since the duplex paper sensor 2 turned on.
- The duplex paper sensor 1 does not turn off when the paper 
with a longitudinal length of 280 mm reaches the standby 
position (about 90 mm from the duplex paper sensor 2). 

0228

Stationary jam at 
duplex paper sensor 2

SR1003

The duplex paper sensor 2 does not turn off when the specified 
time has lapsed since the feed motor started.

Code

Name

Sensor No.

Description

010e

Delay jam at No.2 
delivery section

SR1101

The No.2 delivery sensor does not detect presence of paper within 
the specified time after turning on of the fixing delivery sensor. 

0212

Stationary jam at No.2 
delivery section

SR1101

Absence of paper is not detected within the specified time after 
turning on of the No.2 delivery sensor. 

Summary of Contents for iR2318 series





















































































































































































































































































































Reviews:

No comments