manualshive.com logo in svg

Canon iR2318 series, Service Manual, Page: 262 / 308

Share
Download
Canon iR2318 series Service Manual Download Page 262

Chapter 13  

13-2

13.2 Error Code Details

13.2.1 Error Code Details

0020-4318

Display 
Code

Detail Code Main Cause/Symptom

Countermeasure

E000

0000

Startup error

The temperature detected by the main 
or sub thermistor does not rise to the 
specified value during startup control.

- Check the fixing film connector.
- Replace the fixing film unit.
- Replace the DC controller PCB. 

E001

0000

Abnormally high temperature (detected by main thermistor)

The main thermistor detected an 
abnormally high temperature (240 deg 
C) during temperature control. 

- Check the connector of the fixing film unit.
- Replace the fixing film unit. 
- Replace the DC controller PCB.

0001

Abnormally high temperature (detected by sub thermistor) 

The sub thermistor detected an 
abnormally high temperature (295 deg 
C) during temperature control.

- Check the connector of the fixing film unit.
- Replace the fixing film unit.
- Replace the DC controller PCB.

E002

0000

Low temperature during temperature control. 

The target temperature is not reached 
during temperature control.

- Check the connector of the fixing film unit.
- Replace the fixing film unit.
- Replace the DC controller PCB.

E003

0000

Abnormally low temperature (detected by main thermistor)

After the temperature detected by the 
main thermistor has reached the 
specified value, it does not reach the 
specified value during initial rotation.

- Check the connector of the fixing film unit.
- Replace the fixing film unit.
- Replace the DC controller PCB.

0001

Abnormally low temperature (detected by sub thermistor) 

After the temperature detected by the 
sub thermistor has reached the 
specified value, it does not reach the 
specified value during initial rotation.

- Check the connector of the fixing film unit.
- Replace the fixing film unit.
- Replace the DC controller PCB.

E007

0000

Fixing film sensor failure

The fixing film sensor is faulty. 

- Check the connector of the fixing film 
sensor. 
- Replace the fixing film sensor.
- Replace the DC controller PCB.

E010

0000

Main motor failure

The main motor is faulty. 

- Check the connector of the main motor. 
- Replace the main motor.
- Replace the DC controller PCB.

E019

0001

Waste toner full detection 

The waste toner full state was detected. Replace the drum unit.

E052

0000

Erroneous connection to duplex unit 

Disconnection of the duplex unit was 
detected after power-on, detection of 
normal connection to the duplex unit, 
and start of communication. 

- Check the connectors of the duplex unit and 
DC controller PCB. 
- Replace the duplex controller PCB. 
- Replace the DC controller PCB.

E100

0000

BD detection PCB failure 

The BD detection PCB is faulty.  

- Check the connector of the BD detection 
PCB. 
- Replace the laser scanner unit. 
- Replace the DC controller PCB.

E261

0000

Zero cross signal error

Error in the input frequency when the 
power is turned ON.
Error in the measurements of the 
waveform when the power is turned 
ON.
Zero Cross failed to be detected for 3 
sec or more while the relay was ON.

- Check the Connectors.
- Replace the Power supply PCB.
- Replace the DC Controller PCB.

E716

0000

Erroneous communication with optional cassette

Disconnection of the optional cassette 
was detected after power-on, detection 
of normal connection to the optional 
cassette, and start of communication. 

- Check the connectors of the optional cassette 
PCB and DC controller PCB.
- Replace the optional cassette PCB for 
normal connection.
- Replace the DC controller PCB.

Summary of Contents for iR2318 series





















































































































































































































































































































Reviews:

No comments